Author Topic: Show your clamp racks please.  (Read 5204 times)

Onebean and 1 Guest are viewing this topic.

Offline bobtskutter

  • Posts: 30
Re: Show your clamp racks please.
« Reply #30 on: December 26, 2021, 01:42 PM »
I just hang them from a joist in the roof of my garage.

Bob


Offline 4nthony

  • Posts: 97
    • Slack for Recon Tools
Re: Show your clamp racks please.
« Reply #31 on: December 28, 2021, 07:19 PM »
Some clamp storage I've been building in the last couple weeks for the small french cleat corner of the garage. The clamp racks are pretty similar to what others have posted but I added some small tabs to the front of the racks. I have limited space and tend to bump into them often so I'm hoping the tabs will assist in keeping them in the rack and not falling on my head.

The racks are all about 300mm deep. The larger racks are ~300mm tall while the smaller racks are about ~100mm tall.


« Last Edit: December 28, 2021, 07:24 PM by 4nthony »

Offline Crazyraceguy

  • Posts: 973
Re: Show your clamp racks please.
« Reply #32 on: December 28, 2021, 07:56 PM »
 That's a good looking set-up you have going there 4nthony.
CSX
DF500 + assortment set
PS420 + Base kit
OF1010
OF1400
MFK700 (2)
TS55, FS1080, FS1400 holey, FS1900, FS3000
CT26E + Workshop cleaning set
RO90
RO125
ETS EC 125
RAS115
ETS 125 (2)
TS75
Shaper Origin/Workstation

Offline 4nthony

  • Posts: 97
    • Slack for Recon Tools
Re: Show your clamp racks please.
« Reply #33 on: December 28, 2021, 08:45 PM »
That's a good looking set-up you have going there 4nthony.

Thanks. My previous clamp organization was hanging them off the fire blocking in the walls or placing them in a couple 5 gallon buckets and leaning them into a corner. It's nice to finally have some organization. Wish I could say the same about the rest of the garage! Shops are always a work in progress, right?

Offline Crazyraceguy

  • Posts: 973
Re: Show your clamp racks please.
« Reply #34 on: December 29, 2021, 04:37 PM »
Wish I could say the same about the rest of the garage! Shops are always a work in progress, right?

Absolutely. I'm sort of in the planning stages of some rearrangement of mine right now. I think I'm going to add some more parallel clamps horizontally, around the base of my main assembly table.

You have a pretty good collection of Woodpeckers squares in there too.
CSX
DF500 + assortment set
PS420 + Base kit
OF1010
OF1400
MFK700 (2)
TS55, FS1080, FS1400 holey, FS1900, FS3000
CT26E + Workshop cleaning set
RO90
RO125
ETS EC 125
RAS115
ETS 125 (2)
TS75
Shaper Origin/Workstation

Offline 4nthony

  • Posts: 97
    • Slack for Recon Tools
Re: Show your clamp racks please.
« Reply #35 on: December 29, 2021, 08:12 PM »
You have a pretty good collection of Woodpeckers squares in there too.

Yeah...those squares are somewhat of an addiction.  [embarassed]

The 2616 has been really useful on larger projects. Also, I find that I use it more than the track square to align my guide rails.