Author Topic: MFT Fence Extension  (Read 2692 times)

0 Members and 1 Guest are viewing this topic.

Offline Jersey_Woodworks

  • Posts: 2
MFT Fence Extension
« on: October 13, 2021, 10:41 AM »
The MFT fence extends beyond the length of the table past the fence stop. Walking into that is never good. Considering cutting it back closer to the fence stop to ease workflow in a small 2-car garage but wanted to check if there was another option I am missing. Do not believe Festool offers a smaller length fence to prevent this extension.

Cheers!

Offline jobsworth

  • Posts: 6882
  • Festool Baby.....
Re: MFT Fence Extension
« Reply #1 on: October 14, 2021, 11:11 AM »
Don’t cut the fence

Offline Peter Parfitt

  • Magazine/Blog Author
  • *
  • Posts: 4509
    • New Brit Workshop on YouTube
Re: MFT Fence Extension
« Reply #2 on: October 14, 2021, 01:59 PM »
Ron is right, do not cut it.

Peter

Offline Bob D.

  • Retailer
  • *
  • Posts: 2707
    • My Cordless Workshop
Re: MFT Fence Extension
« Reply #3 on: October 14, 2021, 03:22 PM »
I have thought of doing the same after banging into it more than once in my 10' x 18'
basement shop with very little room. That 6 inches hanging out there is a PITA (actually
it's at kidney level for me). I wore a nice bruise for a couple days after hitting it one time.

I had the hacksaw in my hand ready to strike but decided to put it off telling myself I'd
learned my lesson.

Well, guess what. Nope, I'm as dumb (or clumsy) as the first time and banged into it
again a month later.

But I still haven't bobbed the fence. Doesn't mean I don't want to though. :-)

Tell me why I shouldn't please. And I don't care about resale value.
-----
It's a table saw, do you know where your fingers are?

Offline tsmi243

  • Posts: 248
Re: MFT Fence Extension
« Reply #4 on: October 14, 2021, 05:11 PM »
I say cut it.  Just keep the offcut, and find a way to join it back when you need the capacity for the flag stop.

Offline Peter_C

  • Posts: 1346
Re: MFT Fence Extension
« Reply #5 on: October 14, 2021, 05:36 PM »
I have a different kind of fence but mine doesn't extend beyond the table, and I have not had any issues with my fence being too short, mind you I can easily add extensions onto it for flag stops. *shrugs* My MFT fence is about the same length as the Biesemeyer fence on my table saw, which also happens to be about the same length as my Biesemeyer fence on the table saw sled.

Instead carrying a large heavy object I smashed my hip into the saw rail sticking out the front bending the rear mount. Oops! Dashboard can fix it!

Offline Bob D.

  • Retailer
  • *
  • Posts: 2707
    • My Cordless Workshop
Re: MFT Fence Extension
« Reply #6 on: October 14, 2021, 07:32 PM »
I say cut it.  Just keep the offcut, and find a way to join it back when you need the capacity for the flag stop.

Super Glue !
-----
It's a table saw, do you know where your fingers are?

Offline Jersey_Woodworks

  • Posts: 2
Re: MFT Fence Extension
« Reply #7 on: October 14, 2021, 09:23 PM »
I get the extra fence capacity, but why not cut it? Has anyone done this and regret it? It’s kind of like the miter saw fence debate: does your entire miter saw need a fence? Or is just the miter saw fence (where the cut is being made) all that matters? I’m applying that theory here. What is that extra 6-8 inches hanging off the side of the table going to serve other that cuts and bruises to my hips haha. Just looking for options and discussion here around this since I haven’t found a thread covering this “issue”. Cheers!

Offline Bert Vanderveen

  • Posts: 896
Re: MFT Fence Extension
« Reply #8 on: October 15, 2021, 07:15 AM »
I got rid of the fence. It takes up too much real estate. I use dogs or the UJK fence that uses dogs and has a pretty good stop (I own two UJK’s).
Cheers, Bert Vanderveen

TS55 · TS55R · OF1010 · DF500 · MFT/3 + TSB1-MW 1000 + VL + CMS TS55 + CMS PS300 + LA-CS 70/CMS · CTL Midi · RTS400 · 2 x CXS Li 1,5 · T15+3 Li 4,2 · TI15 Impact Li 4,2 · Centrotec Sets 2008 + 2015 · PSB300 · LR32-SYS · RO150 · KS120 · 2 x MFK700 · RO90 · OFK700 · BS75 · OFK500 · OF2200 · CMS-GE · Vecturo 18 Li · TID 18 · TKS 80 EBS-Set · DTS 400 · ETS EC 125 w 150 pad · Surfix Set · CTL SYS · CT-VA-20 · … | Mirka 1230L P&C | Hammer: A3 31 Silent Power · N4400 · HS950 | TaigaTools: VacPods Pro Set
On order: … [ ! ]

Offline MaineShop

  • Posts: 121
Re: MFT Fence Extension
« Reply #9 on: October 15, 2021, 12:46 PM »
In case it is not obvious you sometimes need all the length for an angled cut when you have the fence at an angle and you still want to use the fence stop.

Offline Bob D.

  • Retailer
  • *
  • Posts: 2707
    • My Cordless Workshop
Re: MFT Fence Extension
« Reply #10 on: October 15, 2021, 01:03 PM »
In case it is not obvious you sometimes need all the length for an angled cut when you have the fence at an angle and you still want to use the fence stop.

Ok, I understand why one might want to have all that length but I have never needed that 6 inches (no, not THAT 6 inches) since I bought my MFT/3. I don't think I would miss it if I trimmed it off. Situation is different for everyone I understand. But if I bang into that thing one more time it's outta here.  [cool]
-----
It's a table saw, do you know where your fingers are?

Offline jobsworth

  • Posts: 6882
  • Festool Baby.....
Re: MFT Fence Extension
« Reply #11 on: November 04, 2021, 09:41 AM »
@Bob D.

@Jersey_Woodworks

Better have it and not need it than to need it and not have it.

You can cut it if you wish. It’s your kit right.

It’s been my experience as soon as you cut it, you’ll need the extra length for something.
Then you’ll be here axing how to cut something longer with a short fence.

So with that being said I recommend rather than cutting the existing fence short, go to Festool and order the short fence they make for the CMS.

You can still get it. It’s about the length you said you need.

Don’t know the part number but you can call them they’ll hook you up or go to ekat and find it.

That way you’ll have the longer fence when you need it. Notice I said when you need it, not if you you need it.

 Cuz you will eventually

Offline Bob D.

  • Retailer
  • *
  • Posts: 2707
    • My Cordless Workshop
Re: MFT Fence Extension
« Reply #12 on: November 04, 2021, 11:13 AM »
I can weld AL with my MIG welder, no problemo.  [big grin]

JK of course. I haven't trimmed it yet. Don't know if I will
but it does get in my way more than it helps, much more.
-----
It's a table saw, do you know where your fingers are?

Offline tsmi243

  • Posts: 248
Re: MFT Fence Extension
« Reply #13 on: November 04, 2021, 12:32 PM »
I say cut it.  Just keep the offcut, and find a way to join it back when you need the capacity for the flag stop.

Super Glue !

That's.... one option, I guess  :)

I was thinking something more like a rail connector.  Shouldn't be too hard to make.