« previous next »
Pages: [1]   Go Down

Author Topic: FOG inspired cabinet installation truck  (Read 20855 times)

0 Members and 1 Guest are viewing this topic.

Offline WPeters

  • Posts: 206
FOG inspired cabinet installation truck
« on: April 22, 2013, 08:02 PM »
Well we had some down time at the shop and i decided it was time to update and organize our install truck! There were lots of good ideas on this forum and I spent a good bit of time checking out some of the organization solutions found here.  I ended up buying 4 sortainers.  (2 new and 2 on ebay...and one of them was kinda accidental!! [unsure])  I also ordered a couple empty systainers.  Below is the finished product (at least for now [wink]).    

The six new sortainers and systainers.



These photos are pictures of the contents in the six sortainers/systainers above starting at the top left and going left to right.






There are more photos of the tool organizer insert i made on this thread Tool insert











A few more....

« Last Edit: April 22, 2013, 08:10 PM by WPeters »
Logged

Offline Michael Garrett

  • Posts: 410
Re: FOG inspired cabinet installation truck
« Reply #1 on: April 22, 2013, 08:23 PM »
Great organization.  What is the source for the snappy tool pouches?
Logged
CT 26 HEPA, MFT/3 (2), TS 75 EQ, OF 1400 EQ,  DF 500 SET, CXS SET, C 15+3 SET, Ti-15 Basic, CENTROTEC INSTALLER SET 98-PC, TRADESMAN/INSTALLER CLEANING SET, DOMINO ASSORTMENT SYSTEM, LR 32 HOLE DRILLING SET, GUIDE RAIL FS 3000 (1), GUIDE RAIL ACCESSORY KIT, GUIDE RAIL FS 1400/2  (2), GUIDE RAIL FS 1900/2  (2), GUIDE RAIL FS 1400/2 LR 32  (1), Veritas MFT Clamping Kit,  Imperial & Metric Zorbo Forstner Bit Sets, RO 90, ETS 150/3, PSB 420 EBQ w/Accessory Kit, WCR-1000, PARALLEL GUIDE SET, CT 26 BOOM ARM SET, Veritas® Drilling Kit, MFK 700 EQ Router Set

Offline WPeters

  • Posts: 206
Re: FOG inspired cabinet installation truck
« Reply #2 on: April 22, 2013, 08:29 PM »
Quote from: Michael Garrett on April 22, 2013, 08:23 PM
Great organization.  What is the source for the snappy tool pouches?

Thanks!  Several years ago we purchased pouches like this at the IWF tool show.  They were a promotional item and since then have been discontinued.  A couple weeks ago i called Snappy and requested a couple more (The ones in the photo).....After a little hesitation they agreed to make these up for me.  (They normally sell to distributors)  I then purchased all the driver bits at craftsman/sears.  http://www.snappytools.com/
Logged

Offline Michael Garrett

  • Posts: 410
Re: FOG inspired cabinet installation truck
« Reply #3 on: April 22, 2013, 08:51 PM »
Thanks for the info.  I'll try and contact them.  How many pieces does it hold, so I'll lnow what to ask for.   Thanks.
Logged
CT 26 HEPA, MFT/3 (2), TS 75 EQ, OF 1400 EQ,  DF 500 SET, CXS SET, C 15+3 SET, Ti-15 Basic, CENTROTEC INSTALLER SET 98-PC, TRADESMAN/INSTALLER CLEANING SET, DOMINO ASSORTMENT SYSTEM, LR 32 HOLE DRILLING SET, GUIDE RAIL FS 3000 (1), GUIDE RAIL ACCESSORY KIT, GUIDE RAIL FS 1400/2  (2), GUIDE RAIL FS 1900/2  (2), GUIDE RAIL FS 1400/2 LR 32  (1), Veritas MFT Clamping Kit,  Imperial & Metric Zorbo Forstner Bit Sets, RO 90, ETS 150/3, PSB 420 EBQ w/Accessory Kit, WCR-1000, PARALLEL GUIDE SET, CT 26 BOOM ARM SET, Veritas® Drilling Kit, MFK 700 EQ Router Set

Offline builderbob

  • Posts: 1375
    • RJP Remodeling
Re: FOG inspired cabinet installation truck
« Reply #4 on: April 22, 2013, 10:11 PM »
Looks great!  I'll give it a test run for a week for you :)

Is that a box van?

Bob
Logged
Kapex, TS55, CMS GE, Carvex 420, Domino DF500, MFK 700, OF 2200, OF 1400, OF 1010, EHL65, RAS 115, RTS 400, RO150, ETS 150/3, ETS 125, CT 22 (2), CXS (2), C-15+3, T-12+3, PSB 300 & more MFT's than i can count!

Offline SRSemenza

  • Global Moderator
  • *
  • Posts: 9960
  • Finger Lakes Region, NY State , USA
Re: FOG inspired cabinet installation truck
« Reply #5 on: April 22, 2013, 11:29 PM »
Hey, nice.

Amazing how much can go into a Sortainer or Systainer isn't it? 

I have that same Craftsman multi level tool tote/box. It was a primary  one for me until I went Systainer nuts.  I always found it to be a pretty good one. I still like it and use it for some general carpentry and painting stuff.  It's not part of my work  kit anymore because  it doesn't fit the rest of my system.

Seth
Logged

Offline joiner1970

  • Posts: 3222
Re: Re: Re: FOG inspired cabinet installation truck
« Reply #6 on: April 23, 2013, 01:20 AM »
Quote from: Michael Garrett on April 22, 2013, 08:23 PM
Great organization.  What is the source for the snappy tool pouches?

They're available here in the UK if you can find a dealer who will ship to you.
Logged

Offline WPeters

  • Posts: 206
Re: FOG inspired cabinet installation truck
« Reply #7 on: April 23, 2013, 06:37 AM »
Quote from: Michael Garrett on April 22, 2013, 08:51 PM
Thanks for the info.  I'll try and contact them.  How many pieces does it hold, so I'll lnow what to ask for.   Thanks.


I'm not certain as i don't have it in front of me.  I believe they called it their "large pouch".  You could also reference the pouch they used for their trade show specials.
Logged

Offline neeleman

  • Posts: 1284
Re: FOG inspired cabinet installation truck
« Reply #8 on: April 23, 2013, 06:47 AM »
Here are some specs of the Snappy Tool Holders (info from Miles TMC):
TH/4-22 pieces at £9.53
TH/1-30 pieces at £9.53
TH/2-60pieces at £11.91
I also think they are quite handy for a variety of Festool Centrotec pieces when you are on a job site instead of carrying a Centrotec systainer with you.
Logged
Festoolian since 1998.
FESTOOL:
OF1010R | AGC18 | TPC18/4 | TID18 | OSC18 | RTSC400Li | CTL MIDI I | SYSROCK BR10 | SYSLITE KAL II | SV-SYS D14 | DSC-AG125FH | CDD9.6 | SYSLITE DUO | DF700 | HKC55 | TXS2.6 | CTL SYS | CXS2.6 | DWC18 | CTWings | BHC18 | CS50 | CMS-OF | MFT/3 | MFT/3-VL | KS120 | TS55 R | PSC420 | PS420 | BS75 | RAS115 | RO90 | RO150 | RS400 | RTS400 | RS300 | LS130 | DX93 | ETS150/5 | ETS150/3 | OF1400 | OFK500 | MFK700 | T18 | EHL65 | CTL26 | CTL22 | WCR1000 | D27-AS Plug-it | D36 UNI-RS | D36x7 | D50x2.5 | FS800 | FS800/2 | FS1080/2 | FS1400/2 (2x) | FS3000/2 | FSK250 | FSK420 | Gecko Dosh | Toolie | CE-SYS-2010 | RB-SYS CART (2x) | LEV1400 | LEV350 | SYS-MFT
PROTOOL:
CHP26 | VCP260 | DSC-AGP125 | DSC-AGP230 | DSG-AGP125 | DRP16

Offline WPeters

  • Posts: 206
Re: FOG inspired cabinet installation truck
« Reply #9 on: April 23, 2013, 06:50 AM »
Quote from: builderbob on April 22, 2013, 10:11 PM

Is that a box van?

Bob

Its a 6500 Chevy box truck.  18' bed.  The bed is lower than most on box trucks and it also has an innovative set of steps that are folded flat, but pull out and self level to whatever surface you're on.  We were hesitant to go to a truck after using a trailer with a ramp for years, but we wanted a moble shop and this has worked great.  We still have the trailer and use it for large jobs.


Quote from: SRSemenza on April 22, 2013, 11:29 PM

I have that same Craftsman multi level tool tote/box. It was a primary  one for me until I went Systainer nuts.  I always found it to be a pretty good one. I still like it and use it for some general carpentry and painting stuff.  It's not part of my work  kit anymore because  it doesn't fit the rest of my system.

Seth

Yeah we used them for years, before this latest foray into systainers  [smile]  That shelf with the six systainers was dedicated for 4 of those totes.  I easily fit everything from 3 of them into 3 systainers (pruning accumulated junk and phasing out some dewalt stuff in the process)  The tools and hardware are so much more accessable now!  The lone tote in the picture is for grommits, leg leveler clips and misc.


Logged

Offline Samo

  • Posts: 639
Re: FOG inspired cabinet installation truck
« Reply #10 on: April 23, 2013, 05:48 PM »
Get more Insurance and a good roll up lock with alarm.

 [embarassed]

Logged
It's The FOG!  Just rotate the screen.

Offline WPeters

  • Posts: 206
Re: FOG inspired cabinet installation truck
« Reply #11 on: April 23, 2013, 07:30 PM »
You can't be too careful that's for sure.  That is a cool video of the truck!  Fastcap is also a great company...I really like Paul's book "2 Second Lean"
Logged

Offline Samo

  • Posts: 639
Re: FOG inspired cabinet installation truck
« Reply #12 on: April 23, 2013, 08:03 PM »
Interesting   [big grin]

I like Paul's personality and I've never even met him.  Total Sales Guy.  Can't fault the guys drive. I'm sure he makes bank.

Best of luck with the truck!  Keeps us posted on the build out.

Sam

« Last Edit: April 25, 2013, 02:47 PM by Samo »
Logged
It's The FOG!  Just rotate the screen.

Offline curt boyer

  • Posts: 203
Re: FOG inspired cabinet installation truck
« Reply #13 on: May 02, 2013, 08:40 PM »
I'm buying a 16' box truck that I'm going to turn into a mobile shop. Do you have a link for the folding stairs?
Thanks
Curt
Logged

Offline WPeters

  • Posts: 206
Re: FOG inspired cabinet installation truck
« Reply #14 on: May 04, 2013, 01:14 PM »
Quote from: curt boyer on May 02, 2013, 08:40 PM
I'm buying a 16' box truck that I'm going to turn into a mobile shop. Do you have a link for the folding stairs?
Thanks
Curt

Well a local company called Devers installs them.  http://jwdeverstruckequipment.com/  I think it is a custom design with them.  We bought the truck a few years old, so not sure what the cost was.  When i got the truck serviced awhile back they commented the stairs are pretty rare because they are so exspensive to put it.  Here are some pictures.
Logged
Pages: [1]   Go Up
« previous next »