Author Topic: UJK Parf Guide Mark II question  (Read 823 times)

0 Members and 1 Guest are viewing this topic.

Offline Wood_Slice

  • Posts: 74
UJK Parf Guide Mark II question
« on: February 12, 2021, 10:51 AM »
I just recently bought the Parf Guide mark 2 and on the very first use I am not sure if I tightened with too much torque or the screw was just bad or because the alen key wasn't good no idea but the tinny little set screw that was inside the stop collar on the 20 mm bit just stripped out. I was forced to drill the set screw out in order to get the drill bit out of the aluminum jig. Anyways long story short does anybody know the thread size on that screw and/or where to get one?
DF 500 + Assortments | ETS EC 125/3 EQ | CT MIDI + CT-Fi| MFT3 + Elements| Installer's Set |

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline TSO_Products

  • Retailer
  • *
  • Posts: 358
    • TSO Products LLC
Re: UJK Parf Guide Mark II question
« Reply #1 on: February 12, 2021, 12:47 PM »
@Wood_Slice  - it would be easier to send you a complete replacement S.S. Clamping collar.

phone me to expedite or email me for a response on Monday

Hans (952) 270-4892 Mobile
info@tsoproducts.com

Hans

Offline Wood_Slice

  • Posts: 74
Re: UJK Parf Guide Mark II question
« Reply #2 on: February 12, 2021, 09:31 PM »
Thank You very much Hans. Will contact you. Appreciate the quick response.
DF 500 + Assortments | ETS EC 125/3 EQ | CT MIDI + CT-Fi| MFT3 + Elements| Installer's Set |

Offline Chris Perren

  • Posts: 146
Re: UJK Parf Guide Mark II question
« Reply #3 on: March 07, 2021, 04:33 PM »
Similar issue - Allen head screw on the stop collar stripped..   I had to drill it out.  Any idea on the size so I can replace with a better screw (i.e. stainless).  Thanks Chris

 

Offline TSO_Products

  • Retailer
  • *
  • Posts: 358
    • TSO Products LLC
Re: UJK Parf Guide Mark II question
« Reply #4 on: March 08, 2021, 07:22 AM »
Chris,
sorry you encountered this problem.

We will check it and let you know. Our own Clamping Collar on the Parallel Guide FlipStop uses a custom combination of thread and socket size screw but may work for you.

More tomorrow - if you don't see it here, drop me an email

Hans

Offline savsuds

  • Posts: 38
Re: UJK Parf Guide Mark II question
« Reply #5 on: March 25, 2021, 07:04 PM »
I had the same problem after making several MFT style table tops. I replaced it with a 10mm stop collar from Powertec.
Hobbyist just trying to have fun and not let my OCD ruin it for me.