« previous next »
Pages: [1]   Go Down

Author Topic: Ideas on how to remove outfeed roller on jet JP-12?  (Read 406 times)

0 Members and 1 Guest are viewing this topic.

Offline festal

  • Posts: 499
Ideas on how to remove outfeed roller on jet JP-12?
« on: March 05, 2023, 06:48 PM »
So my outfeed roller is shredded to pieces and I finally got replacement but I can’t seem to be able to remove the screw holding the sprocket in place. Outfeed roller is round and nothing to grab on. I tried to put a piece of wood under the sprocket but it just keeps shredding when I’m trying to unscrew the nut.
Any ideas on what I can do here?




Sent from my iPhone using Tapatalk
Logged
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

Offline MikeGE

  • Posts: 428
Re: Ideas on how to remove outfeed roller on jet JP-12?
« Reply #1 on: March 05, 2023, 07:05 PM »
I would put the chain and the belts back on and use them to hold the sprocket in place while using an impact driver to remove the nut.
Logged

Offline festal

  • Posts: 499
Re: Ideas on how to remove outfeed roller on jet JP-12?
« Reply #2 on: March 05, 2023, 07:24 PM »
Quote from: MikeGE on March 05, 2023, 07:05 PM
I would put the chain and the belts back on and use them to hold the sprocket in place while using an impact driver to remove the nut.
Hmm. Will try it


Sent from my iPhone using Tapatalk
Logged

Offline tjbnwi

  • Posts: 6699
  • No longer in Cedar Tucky Indiana
Re: Ideas on how to remove outfeed roller on jet JP-12?
« Reply #3 on: March 05, 2023, 07:34 PM »
That’s a nylock nut, impact in short bursts.

Also make sure they are not left hand threads.

Tom
Logged

Offline festal

  • Posts: 499
Re: Ideas on how to remove outfeed roller on jet JP-12?
« Reply #4 on: March 05, 2023, 07:38 PM »
Quote from: MikeGE on March 05, 2023, 07:05 PM
I would put the chain and the belts back on and use them to hold the sprocket in place while using an impact driver to remove the nut.
Worked perfectly. Thank you


Sent from my iPhone using Tapatalk
Logged

Offline festal

  • Posts: 499
Re: Ideas on how to remove outfeed roller on jet JP-12?
« Reply #5 on: March 05, 2023, 07:39 PM »
Quote from: tjbnwi on March 05, 2023, 07:34 PM
That’s a nylock nut, impact in short bursts.

Also make sure they are not left hand threads.

Tom
Didn’t need impact. Once chain was on and rollers engaged it locked in place and I was able to unscrew the nut


Sent from my iPhone using Tapatalk
Logged
Pages: [1]   Go Up
« previous next »