« previous next »
Pages: [1]   Go Down

Author Topic: Dedicated router table vs built into bench  (Read 3371 times)

0 Members and 1 Guest are viewing this topic.

Offline 3PedalMINI

  • Posts: 493
    • Signature Sound & Video
Dedicated router table vs built into bench
« on: February 09, 2018, 11:08 AM »
Let me start out by saying I’m in a desperate need of consolidating my work shop. One of the things I’m trying todo is consolidate some things into a work bench. I’m going to build a Paulk workbench type table but make it movable within the garage. I’ll make some systainer storage and a place for my CT and a place to put my planner and scroll saw underneath. Overall this table needs to be my workbench, assembly etc etc 

One of the areas where I can save a lot of space is to move my router table into the work bench. I have a Jessem Lift and table right now but I would just shift the lift into the workbench. I’m worried that it’s not going to be as accurate as my jessem table. I would get good quality ply for the top obviously and use the jessem fence on the bench when needed.

Thoughts on this? I don’t use my router a lot but do use it a lot for cabinetry (beaded face frames etc) I see a lot of plans out there that just use plywood for the top so maybe I’m overthinking this?

Logged
The Bitterness of poor quality remains long after the sweetness of low price is forgotten -Benjamin Franklin

Professional Custom Audio Video System Designer/Installer serving Southern - Middle NJ, Eastern PA & the Surrounding Shore Points.
www.sigsv.com

Kapex 120,TS55,RO150,ETS125,CT-26,CT-MIDI,Tradesmen Cleaning Kit, Festool Ratchet Kit, Sys-lite, Sys Roll Cart, T18 +3, 2013 Centrotec Kit, Carvex 420, Carvex Accessory Kit, CXS,RO90, TI15 and Various Festool Systainers
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

Offline grobkuschelig

  • Posts: 735
Re: Dedicated router table vs built into bench
« Reply #1 on: February 09, 2018, 12:02 PM »
If you are concerned about the top surface, take a look at HPL, super rigid and flat. I just purchased some for an upcoming „MFTB-Sys“ (the benchworks/ timtool Version)with integrated router...
Logged

Offline live4ever

  • Posts: 860
Re: Dedicated router table vs built into bench
« Reply #2 on: February 09, 2018, 01:34 PM »
Top just needs to be reasonably slick and flat.  That's about it.  I take my lift and drop it in to the Paulk workbench once in a while.  I have a couple of coats of I believe shellac on fairly meh-quality plywood.  The surface isn't glass smooth but it's slick enough to work just fine as a router table surface.  And since the Paulk WB is essentially a torsion box, the top is flat enough. 

If I really wanted a slicker surface, I'd just rout out a shallow section and inlay some laminate.
Logged
Current systainer to productivity ratio:  very high

Offline neilc

  • Posts: 3073
Re: Dedicated router table vs built into bench
« Reply #3 on: February 09, 2018, 06:56 PM »
I built a Paulk top with a rockler router insert and systainer storage for my son.  Router is at one end and the other is a table saw outfeed.  We inset T-track for fence adjustment and included a miter gauge slot.  Wired an interior receptacle into a switch set into the side of the bench for easy router power control.  It works really well. 

Positives - smaller footprint, larger work surface is handy on some routing tasks, dust is somewhat contained in the Paulk 'cavity' below the top as we did put a divider to deal with that.

Downsides - You CAN lose bench space when you are doing assembly / routing for things like cabinet doors or drawers.   You just need to plan better so that if you drop the router below the top and remove the fence you are ready for assembly.  I have a separate bench, MFT table and CMS table which I like because I frequently will be cutting / routing and assembling or tweaking fit and finish so being able to move between the router and bench / assembly is an advantage.

The base we built is 35 x 67 with four Systainer storage bays under it and a center cavity for larger items.  The Paulk style top is 36 x 76.  Make sure you get double locking casters for stability.  The bench we built is pretty heavy but would move if we didn't use the casters that lock from rolling and rotating.

I don't have a photo or drawing of the bench but attached is the base -


« Last Edit: February 09, 2018, 07:02 PM by neilc »
Logged

Offline 3PedalMINI

  • Posts: 493
    • Signature Sound & Video
Re: Dedicated router table vs built into bench
« Reply #4 on: February 10, 2018, 04:55 PM »
Thanks guys! I like the idea of doing the top out of HPL. Not sure how a router will do cutting out the 20mm holes but I suppose that’s what harbor freight is for :D

@neilc

That’s EXACTLY what I was going to build. It’s like you read my mind or something lol! I love the Kraft paper roller, that’s a must for me! Did you guys use the LR32 system for the systainer storage or did you just evenly space the drawers and drill the pins where needed?
Logged
The Bitterness of poor quality remains long after the sweetness of low price is forgotten -Benjamin Franklin

Professional Custom Audio Video System Designer/Installer serving Southern - Middle NJ, Eastern PA & the Surrounding Shore Points.
www.sigsv.com

Kapex 120,TS55,RO150,ETS125,CT-26,CT-MIDI,Tradesmen Cleaning Kit, Festool Ratchet Kit, Sys-lite, Sys Roll Cart, T18 +3, 2013 Centrotec Kit, Carvex 420, Carvex Accessory Kit, CXS,RO90, TI15 and Various Festool Systainers

Offline neilc

  • Posts: 3073
Re: Dedicated router table vs built into bench
« Reply #5 on: February 10, 2018, 05:28 PM »
I have the LR32 but we actually just used a Rockler drilling jig -


http://www.rockler.com/jig-itreg-shelving-jig-jig-it174-shelving-jig-set-template-self-centering-bit


It's fast and easy for short cabinets like this one.  We just aligned it flush to the bottom and used a TSO triangle to keep it square.  They offer both a 1/4" and a 5mm bit.


Logged
Pages: [1]   Go Up
« previous next »