Author Topic: Cubitron with Festool sanders  (Read 7659 times)

0 Members and 1 Guest are viewing this topic.

Offline Cheese

  • Posts: 8906
Re: Cubitron with Festool sanders
« Reply #60 on: September 08, 2021, 09:54 PM »
Which pad is the correct one to use for mesh paper?

The 492271 StickFix Interface Pad or something else.

Festool offers a series of protection pads. They're all about 1/8" thick.

203344 = 125 series
203343 = 150 series
203346 = RTS series
203347 = DTS series

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Online Lincoln

  • Posts: 152
Re: Cubitron with Festool sanders
« Reply #61 on: September 08, 2021, 11:06 PM »
Which pad is the correct one to use for mesh paper?

The 492271 StickFix Interface Pad or something else.

No, that's for following curves/round overs etc. You want a 'pad saver', which protects the hook and loop from damage caused by the mesh. They're a disposable item, available from Mirka.

Offline Bob D.

  • Posts: 2295
Re: Cubitron with Festool sanders
« Reply #62 on: September 09, 2021, 05:44 AM »
Thanks Cheese and Lincoln. Sounds like a trip to Woodcraft is in order.

Only bad part is I'll probably come home with more than just the pad.  [big grin]

Haven't been to Woodcraft in over a year with the pandemic. Might be
time to take a trip over the bridge into Delaware. It's 35 miles one way
and a $5 bridge toll so I have to make it worth my while. I don't think
there is a Woodcraft in all of NJ.

Update: Glad I called before I headed over there as they have none in stock
so I order off the web. Should be here by Saturday. They come two to a pack
for $13.00
« Last Edit: September 09, 2021, 09:36 PM by Bob D. »
-----
It's a table saw, do you know where your fingers are?

Offline afish

  • Posts: 601
Re: Cubitron with Festool sanders
« Reply #63 on: September 09, 2021, 08:51 AM »
Which pad is the correct one to use for mesh paper?

The 492271 StickFix Interface Pad or something else.

Not sure about others but the last time I got some Diablo mesh it came with an interface pad in the package.  I agree with Alex however I was not impressed with the Diablo mesh I dont remember exactly what I was sanding but I do remember once it hit a corner or edge it disintegrates fast

I use and love the film backed Cubitron paper. It is the only sandpaper I buy now.  I will say on some sanders such as ETS 125 Req I feel like the dust collection does suffer a bit with the film backed disks.  No fancy scientific tests were done to come to that conclusion just my personal and objective observation.  Im going to give the cube mesh a try and really, really hope its more durable than the Diablo.  If so it could be the perfect disc if it performs like in the KM video. 

Offline Cheese

  • Posts: 8906
Re: Cubitron with Festool sanders
« Reply #64 on: September 09, 2021, 10:20 AM »
I use and love the film backed Cubitron paper. It is the only sandpaper I buy now.  I will say on some sanders such as ETS 125 Req I feel like the dust collection does suffer a bit with the film backed disks.  No fancy scientific tests were done to come to that conclusion just my personal and objective observation. 

Here's a recent example on teak outdoor furniture. The results are pretty obvious. Once I get back to this teak sanding project, I'll try attaching the MIDI to the ETSC and look at those results. 

1. An ETSC 125 with only the vacuum bag
2. An ETS EC 125/150 with a MIDI 1 attached.










« Last Edit: September 09, 2021, 10:22 AM by Cheese »

Offline afish

  • Posts: 601
Re: Cubitron with Festool sanders
« Reply #65 on: September 09, 2021, 10:27 AM »
are you saying you think the dust collection with the 3m cube is just as good as with granat?

Offline Cheese

  • Posts: 8906
Re: Cubitron with Festool sanders
« Reply #66 on: September 09, 2021, 10:50 AM »
are you saying you think the dust collection with the 3m cube is just as good as with granat?

For the ETSC 125 if you're using the dust bag and relying on the internal vac fan on the sander, the larger diameter Granat holes do a lot better job.

For the ETS EC while using Cubitron I also cranked up the amount of suction on the MIDI and that now does as well as the Granat.

It will be interesting to attach the MIDI to the ETSC 125 and see if that helps dust extraction. I think it will I just don't know how much. I think you're also somewhat limited because of the number of holes in the 5" pad versus the 6" pad.

The 5" has 9 large holes and that's it.
The 6" has 16 large holes, 16 medium holes and 38 small holes.

Offline jussi

  • Posts: 399
Re: Cubitron with Festool sanders
« Reply #67 on: September 09, 2021, 11:05 AM »
Thanks for the review cheese. I have an ets ec 150 and Etsy 125.  I only had the 5” Cubitron but recently ordered the 6”.  I have a ct 26 so I’m curious to see how well the dc will perform with larger diameter discs and larger sander.  The 5” was ok but not great for me.
« Last Edit: September 09, 2021, 11:44 AM by jussi »

Offline guybo

  • Posts: 146
Re: Cubitron with Festool sanders
« Reply #68 on: September 09, 2021, 09:23 PM »
good review

Offline xedos

  • Posts: 495
Re: Cubitron with Festool sanders
« Reply #69 on: September 25, 2021, 09:47 PM »
Quote
Not sure about others but the last time I got some Diablo mesh it came with an interface pad in the package.  I agree with Alex however I was not impressed with the Diablo mesh I dont remember exactly what I was sanding but I do remember once it hit a corner or edge it disintegrates fast

Diablo’s interface pad doesn’t work (actually align) with Festool’s hole patterns.  You’ll need to use Festool’s interface pads with whatever brand mesh abrasive you choose if you want the dust collection to function properly.

Mesh disintegrates when you hit a sharp or rough edge, or metal nail, screw, ect.  Matters not whether the disc is from Diablo, Mirka , or Festool.  It’s one of the drawbacks of the type.

Is it the best?   Prob. not, but at roughly 35cents a disc on sale it’s a top contender for value.