Author Topic: Bosch GET75-6N to Festool CT26 adapter?  (Read 739 times)

0 Members and 1 Guest are viewing this topic.

Offline KitShickers

  • Posts: 2
Bosch GET75-6N to Festool CT26 adapter?
« on: April 30, 2021, 12:06 PM »
Hello all,
New to the forum.  I was hoping someone would know of an adapter that will work to connect my Bosch GET75 to my Festool CT26.  Any advice would be greatly appreciated. Thanks in advance!

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline pixelated

  • Posts: 275
Re: Bosch GET75-6N to Festool CT26 adapter?
« Reply #1 on: April 30, 2021, 01:40 PM »
I believe the Bosch VAC024 adapter will connect to a Festool 36mm hose, according to the description I found, that adapter may be included with the sander. I don't know if it helps, but the dust port adapters on my Bosch Colt router fit my 27 inch Festool hose without any other adaptation. I use the VAC024 adapter to hook my Bosch miter saw to a FT 36mm hose (assuming I'm remembering the part number correctly).

Offline Peter_C

  • Posts: 1066
Re: Bosch GET75-6N to Festool CT26 adapter?
« Reply #2 on: April 30, 2021, 03:48 PM »
Welcome to the FOG :)

I thought the Bosch dust connection was the same as Festool at around 27mm, which means the hose that comes with the CT26 should work. The Bosch sander also includes hose adapters. My Bosch Jig Saw connects to the Festool hose without an adapter.

Offline RustE

  • Posts: 601
Re: Bosch GET75-6N to Festool CT26 adapter?
« Reply #3 on: April 30, 2021, 05:56 PM »

I use the VAC024 adapter to hook my Bosch miter saw to a FT 36mm hose (assuming I'm remembering the part number correctly).

I think you’re correct:
https://www.toolnut.com/bosch-vac024-vacuum-hose-adapter-19-mm-port.html

Might also be able to use this:
https://www.zoro.com/nilfisk-tool-adapter-w12a502-505-302000535/i/G1984958/

Offline Imemiter

  • Posts: 191
Re: Bosch GET75-6N to Festool CT26 adapter?
« Reply #4 on: April 30, 2021, 08:18 PM »
My GET75-6n fits the Festool 27mm nozzle better than some of my Festools do. Looking at you OF 1010!
« Last Edit: April 30, 2021, 08:48 PM by Imemiter »
CSX T18+3 TID18 HKC55 OSC18 OS400 OF1010 LR32 DF700 RAS115 DTS400 ETC125 CTSys CTMidi CT-VA

Offline tsmi243

  • Posts: 59
Re: Bosch GET75-6N to Festool CT26 adapter?
« Reply #5 on: April 30, 2021, 10:32 PM »
Looking at you OF 1010!

Amen.  Try one of those 3D printed adapters for the oval ports.  The one I have is from ToolCurve, it's fantastic

Offline KitShickers

  • Posts: 2
Re: Bosch GET75-6N to Festool CT26 adapter?
« Reply #6 on: May 03, 2021, 11:22 PM »
Thanks for the reply guys.  I have the 27mm hose so I should be good to go it sounds.  THanks!