Author Topic: White oak dining table  (Read 493 times)

0 Members and 1 Guest are viewing this topic.

Offline kayak323

  • Posts: 3
White oak dining table
« on: September 09, 2020, 09:11 AM »
My daughter asked if I would build her a dining table for her new house. She gave me a rough sketch of a table she found on the internet. With this to go on, I made the table from white oak and mitered the four table legs to make the 4 1/2″ width and fastened them with the Festool Domino 500. The table was hand scraped to match her wood floors and measures 98 1/2″ long by 43″ wide and the top was fastened with tabletop fasteners slotted into the added rails. The stain was Minwax Provencial and it was finished with 6 hand-rubbed coats of General Finishes Arm-R-Seal oil-based semi-gloss. grain was filled with AquaCote clear tinted with Transtint Mission Brown.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline David

  • Posts: 476
  • Author/speaker/advisor to entrepreneurial experts.
    • A few pieces that I’ve built
Re: White oak dining table
« Reply #1 on: September 09, 2020, 02:06 PM »
Beautiful! How did you attach the four mitered decorative pieces on each of the legs? The parts that look like a frame?
Fifth book (less interesting than woodworking) at http://www.expertise.is

Offline kayak323

  • Posts: 3
Re: White oak dining table
« Reply #2 on: September 10, 2020, 06:15 AM »
I glued the pieces and used pin nails.

Offline ear3

  • Posts: 4123
Re: White oak dining table
« Reply #3 on: September 10, 2020, 09:26 AM »
Congratulations @kayak323 this came out really well, the mitered legs especially.
Kapex KS 120 w/UG Cart and Extensions • CXS Set • T 18+3 w/Centrotec Installer's Set • PDC 18/4 • TID 18 • TS 75 • TSC 55 • HKC 55 w/250, 420 and 670 FSK rails • Carvex 420 w/Accessory Kit • Domino 500 Set • Domino 700 XL • OF 2200 w/Base Accessory Kit • OF 1400 • OF 1010 • MFK 700 EQ Set • LR 32 • MFS 400 w/2000, 1000, and 700 extensions • Rotex 90 • Rotex 150 • LS 130 • ETS-EC 150/5 • ETS-EC 150/3 • Pro 5 LTD • RTS 400 • RAS 115.04 • RS 2 • HL 850 • Vecturo OS 400 • AGC 18-115 • CT 26 w/BT module • CT Sys w/Long-Life Bag • MFT/3

Offline Don T

  • Posts: 1979
  • Phoenix, Az
Re: White oak dining table
« Reply #4 on: September 10, 2020, 09:29 AM »
Looks great!  Love the design.
RO150, C12, DF 500 Q, CT33, TS75, MFT3, Kapex 120, MFT3/Kapex, MFK 700, RO 90, ETS150/3, CT22, Centrotec Installers Kit, Parallel Guides & Ext, Carvex, OF1400, LR32 Set, MFS400 w/700 rails, KA UG Set, First Aid Kit, RTS 400 EQ, Vecturo OS400 Set, CT Wings, CT Drill Guide, Pro 5, CXS, C18, HL850, Vac Sys set

Offline JimD

  • Posts: 474
Re: White oak dining table
« Reply #5 on: September 10, 2020, 12:15 PM »
Looks great!