Author Topic: Walnut Stool  (Read 1137 times)

0 Members and 1 Guest are viewing this topic.

Offline rmhinden

  • Posts: 436
Walnut Stool
« on: March 26, 2021, 08:01 PM »
I finished the stool for my daughter.   Walnut with maple wedges.   

It involved making square wood into round wood and drilling angled holes.    First time I have considered getting a wood lathe, but managed to make the round tenons on my router table with a jig.     

I may make a few more in different sizes and wood species.    As you can see in the last picture, one of our cats approves.

Bob


Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline CeeJay

  • Posts: 323
Re: Walnut Stool
« Reply #1 on: March 26, 2021, 08:09 PM »
Nice work Bob. Looks good.


Sent from my iPad using Tapatalk

Offline Birdhunter

  • Posts: 3446
  • Woodworker, Sportsman, Retired
Re: Walnut Stool
« Reply #2 on: March 26, 2021, 08:51 PM »
Nice project, but a lathe is sheer joy.
Birdhunter

Offline Thompmd

  • Posts: 241
Re: Walnut Stool
« Reply #3 on: March 28, 2021, 09:42 AM »
Looks great, I’m a big fan of Walnut 😀
Sawstop Industrial Saw, TS75,2 800,2 1400 & 2700 rails, CT36, Rotex RO 150 FEQ, CT-VA-20, Carvex PS 420 EBQ, Carvex acc. ZH-SYS-PS 400, Kapex KS 120, CT Cyclone Dust Collection Pre-Separator CT VA 20, DF 500 Q Set, Domino 1,060pc Tenon Assortment, UG-KA-SET Portable Imperial Stand & Extensions,OF1400 EQ-F-Plus, MFT/3, MFT-SP, FS-HZ 160, TSC 55, T18 E

Offline JonathanJung

  • Posts: 155
  • www.timberlightdesigns.com
    • Timberlight Designs
Re: Walnut Stool
« Reply #4 on: March 29, 2021, 12:31 AM »
I'd be curious what the router table jig looks like. Did you just use a roundover bit 4x?

Offline rmhinden

  • Posts: 436
Re: Walnut Stool
« Reply #5 on: March 29, 2021, 12:58 AM »
Thanks for the comments!

I'd be curious what the router table jig looks like. Did you just use a roundover bit 4x?

Here is a picture.  I used a 3/4" straight bit to make the tenons.     

I did use a round over bit to round the edges of the legs and the top.   The legs are not fully round, just the tenons.  There was a lot of trial and error to learn how to do it and get the bit height set correctly.    I used a test leg, but the legs were supposed to be longer, but my first attempt didn't work out too well :-)

Bob




Offline jarbroen

  • Posts: 351
Re: Walnut Stool
« Reply #6 on: April 01, 2021, 11:13 AM »
Nice job on the stool and I like your MacGyver solution to tenons(well, he would have used a pocket knife and duct tape, but...).
I like the wedge detail too.

In addition to the lathe there are actually round tenon makers you can get.  Kinda looks like a hole saw with teeth on the inside.  I haven't used one but researched and they look pretty handy.

And if you decide you want a lathe(because they are fun!) check out the Jet 1221VS.  Excellent starter/intermediate.  There's also a smaller Nova that's supposed to be really nice - I think it's shorter on the length of spindles you can do.