Author Topic: New project started (rush job)  (Read 695 times)

0 Members and 1 Guest are viewing this topic.

Offline Crazyraceguy

  • Posts: 2111
New project started (rush job)
« on: October 06, 2022, 06:12 PM »
This morning I got interrupted and pulled off of the one I was working on, for a rush job.
It was apparently slow going through the process, so when it hit the floor, it was already short of time. I started it at 10am by cutting some of the exterior panels while the CNC guys cut out the ribs (studs) and the top/bottom plates.
The first pic shows the cart with the parts, as they come to me. Second shot is the panels that I cut. The rest are the progress to this point. (5 hours)
CSX
DF500 + assortment set
PS420 + Base kit
OF1010
OF1010F
OF1400
MFK700 (2)
TS55, FS1080, FS1400 holey, FS1900, FS3000
CT26E + Workshop cleaning set
RO90
RO125
ETS EC 125
RAS115
ETS 125 (2)
TS75
Shaper Origin/Workstation/Plate
MFT clamps set
Installers set
Centrotech organizer set
Socket/Ratchet set

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Muttley000

  • Posts: 71
Re: New project started (rush job)
« Reply #1 on: October 06, 2022, 09:41 PM »
Interesting build!
ETS EC 150
TS55 FEQ
CT 36

Offline Birdhunter

  • Posts: 3915
  • Woodworker, Sportsman, Retired
Re: New project started (rush job)
« Reply #2 on: October 06, 2022, 10:17 PM »
What is it?
Birdhunter

Offline Crazyraceguy

  • Posts: 2111
Re: New project started (rush job)
« Reply #3 on: October 07, 2022, 07:42 PM »
It is the outward facing counter for a cafe, in a church. There is an L shaped section that goes behind it, in a corner. This piece goes across the front, for serving customers.
Finished it today, 13 hours total time, for my part. The Solid Surface guys finished the tops today too, or were very close anyway. The back side of this gets filled with cabinets, but I don't know the status there?
I went from the blob, monolithic thing, to this with 3 colors.
Not too many people crazy enough to miter-fold from a flat to a radius, sure why not? Let's give it a go...
CSX
DF500 + assortment set
PS420 + Base kit
OF1010
OF1010F
OF1400
MFK700 (2)
TS55, FS1080, FS1400 holey, FS1900, FS3000
CT26E + Workshop cleaning set
RO90
RO125
ETS EC 125
RAS115
ETS 125 (2)
TS75
Shaper Origin/Workstation/Plate
MFT clamps set
Installers set
Centrotech organizer set
Socket/Ratchet set