Author Topic: Christmas gift for my daughter  (Read 1759 times)

0 Members and 1 Guest are viewing this topic.

Offline VirTERM

  • Posts: 104
Christmas gift for my daughter
« on: December 21, 2019, 08:12 PM »
Just finished working on a gift for my daughter, 60”x40”x1-3/4” walnut table with metal legs. I used Odies oil, 2 coats, after sanding it to 600.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline lshah72414

  • Posts: 116
Re: Christmas gift for my daughter
« Reply #1 on: December 22, 2019, 07:37 AM »
Your daughter is going to love that table( i assume that is her putting the legs on). It is absolutely gorgeous! Nice job.

Offline VirTERM

  • Posts: 104
Re: Christmas gift for my daughter
« Reply #2 on: December 22, 2019, 09:02 AM »
Thank you.
Yes, she can not wait until the table will be in her dinning room.  [big grin]

Offline ultane

  • Posts: 88
Re: Christmas gift for my daughter
« Reply #3 on: December 22, 2019, 11:51 AM »
Great job. She’ll cherish it for the rest of her life!
I might be wrong… Just ask my X...

Offline Dogberryjr

  • Posts: 157
Re: Christmas gift for my daughter
« Reply #4 on: December 22, 2019, 01:04 PM »
Beautiful. How thick was the stock to start with?

Offline harry_

  • Posts: 1341
Re: Christmas gift for my daughter
« Reply #5 on: December 22, 2019, 05:23 PM »
That is certainly a beautiful looking table!
Disclaimer: This post is for educational and entertainment purposes only. Any resemblance to real persons, living or dead is purely coincidental. Void where prohibited. Some assembly required. Batteries not included. Contents may settle during shipment. Use only as directed. No other warranty expressed or implied. This is not an offer to sell securities. May be too intense for some viewers. No user-serviceable parts inside. Subject to change without notice. One size fits all (very poorly).

Offline VirTERM

  • Posts: 104
Re: Christmas gift for my daughter
« Reply #6 on: December 22, 2019, 05:36 PM »
Beautiful. How thick was the stock to start with?
I managed to source rough 8/4 walnut, end up with just a bit over 1-3/4"

Offline Bigdaddy65

  • Posts: 24
Re: Christmas gift for my daughter
« Reply #7 on: December 23, 2019, 08:29 AM »
Beautiful table.

Did you make the legs If not, where did you get them?

Offline VirTERM

  • Posts: 104
Re: Christmas gift for my daughter
« Reply #8 on: December 23, 2019, 09:31 AM »
Beautiful table.

Did you make the legs If not, where did you get them?
Thank you. As time was pressing, I purchased the legs from Rusty Designs, very good quality, and quick service.

Offline jobsworth

  • Posts: 6738
  • Festool Baby.....
Re: Christmas gift for my daughter
« Reply #9 on: December 23, 2019, 12:32 PM »
Very nice. What a great Xmas present. Im sure everytime they use it, have guest over etc they'll appreaciate your gift to them.

Offline VirTERM

  • Posts: 104
Re: Christmas gift for my daughter
« Reply #10 on: December 24, 2019, 01:16 PM »
Very nice. What a great Xmas present. Im sure everytime they use it, have guest over etc they'll appreaciate your gift to them.
Thanks

Offline Mario Turcot

  • Posts: 1288
Re: Christmas gift for my daughter
« Reply #11 on: December 24, 2019, 10:26 PM »
Very nice work  [thumbs up] & thank you for legs link. They have a large selection compare to KJP  [big grin]
Mario

Offline VirTERM

  • Posts: 104
Re: Christmas gift for my daughter
« Reply #12 on: December 28, 2019, 07:37 AM »
Very nice work  [thumbs up] & thank you for legs link. They have a large selection compare to KJP  [big grin]
not the same quality as KJP's, but still acceptable and the price is less than a half. The thickness is 1/8".