Author Topic: What - non Festool - tool / workshop related gizmo/stuff did you buy today?  (Read 76439 times)

0 Members and 1 Guest are viewing this topic.

Offline rst

  • Posts: 2227
Ordered a Versa vise from Willburtversavise.com

Offline Richard/RMW

  • Posts: 1915
Ordered a Versa vise from Willburtversavise.com

Seems to be a lot of that going around...

RMW
As of 10/17 I am out of the Dog business and pursuing other distractions. Thanks for a fun ride!

Offline Dick Mahany

  • Posts: 505
Ordered a Versa vise from Willburtversavise.com

Seems to be a lot of that going around...

RMW

True and we know who was responsible for starting all of this  [smile]

Offline rst

  • Posts: 2227
This site has been a wonderful source of new tools we never knew we needed.

Offline Richard/RMW

  • Posts: 1915
Ordered a Versa vise from Willburtversavise.com

Seems to be a lot of that going around...

RMW

True and we know who was responsible for starting all of this  [smile]

Touché  [big grin]

RMW
As of 10/17 I am out of the Dog business and pursuing other distractions. Thanks for a fun ride!

Offline HarveyWildes

  • Posts: 849
From Lee Valley, I got a set of Veritas flushing chisels with an extra handle, and a plane screwdriver.  I've got a set of Veritas mortise chisels on the way.

Offline montyss

  • Posts: 34
Hammer A3-31 arrived  [wink]

Offline Alanbach

  • Posts: 396
Thanks to @ryanwichman I recently became aware of FastCap.com. First I ordered their TrackRack products and hung my rail on my garage door. In that shipment I received a couple of their tape measures. Much to my chagrin and to my extreme enjoyment I also received their catalog in that shipment. Well that lead to the purchase of their Best Fence system which arrived a few days ago. My OCD didn’t end there. I received this today. Like my wife always says, woodworking is just the cover story for the REAL addiction that is tool collecting!

Offline rst

  • Posts: 2227
Alanbach, your wife is waay tooo perceptive, you're never going to get anything by her.

Offline Alanbach

  • Posts: 396
@rst - ha! You are about 36 years behind me on that observation. The good news is she is good with it!!! Our daughter is a Social Worker that does drug and alcohol addiction counseling and she jokingly calls my wife my tool enabler😊. Apparently every addict has one😊!

Offline RKA

  • Posts: 1720
Not woodshop related, but this is one of those time-savers or problem-solvers that some may find useful.  VIM Tools VHC77 stubby bit set.  The bits are 16mm long vs that standard 25mm and the ratchet is a bit shallower than most as well.  The set comes with a full complement of everything Audi shoved into my engine bay and a few others for good measure.  I swear the engineers over there go to a local nut and bolt warehouse and choose one of everything.  To make matters worse, they aren't consistent from car to car.  One might have a T30 for a particular application and the other will have an M8 triple square. 

Anyway, the set doesn't come cheap.  $80-90 on Amazon.  Here is a pic comparing the familiar Wera ratchet with the included T30 vs. the VIM ratcheting wrench with their 16mm T30.

-Raj

Offline Michael Kellough

  • Posts: 4172
Thanks for the tip Raj!

I’ve had a situation where a 1” bit would fit into the head of the fastener but there wasn’t enough clearance to unscrew the fastener.

Offline Cheese

  • Posts: 6385
Not woodshop related, but this is one of those time-savers or problem-solvers that some may find useful.  VIM Tools VHC77 stubby bit set.  The bits are 16mm long vs that standard 25mm and the ratchet is a bit shallower than most as well.

Anyway, the set doesn't come cheap.  $80-90 on Amazon.  Here is a pic comparing the familiar Wera ratchet with the included T30 vs. the VIM ratcheting wrench with their 16mm T30.

Very interesting...I chased down the Snap-on tool guy last week and purchased this Blue-Point 1/4" hex ratchet. Raj does this look familiar?






Offline RKA

  • Posts: 1720
@Cheese LOL!  Yeah, SO fills out their tool line with odds and ends from lots of other sources.  There is a thread in garagejournal where you can find the OEM's or alternate brands that don't come with the SO tax. 

If access and reaching fasteners in hidden places is a frequent challenge, might I also suggest getting the HBR12 ratcheting wrench.  It's 12" long, which can help or hurt, but it has a pivoting head on one side.

https://www.vimtools.com/Flyers/HBR12%20FLYER.pdf

Oh, and don't chase the SO guy for this one, it's says "made exclusively for VIM Tools" on the flyer.   [tongue]
-Raj

Offline Cheese

  • Posts: 6385
@Cheese LOL!  Yeah, SO fills out their tool line with odds and ends from lots of other sources.  There is a thread in garagejournal where you can find the OEM's or alternate brands that don't come with the SO tax. 

That's funny Raj...the set I purchased even came with the Blue-Point branding applied.


Offline SRSemenza

  • Global Moderator
  • *
  • Posts: 8926
  • Finger Lakes Region, NY State , USA
I've got a couple of the extra short bits that I use in the Wera ratchet (smallest one). They come in handy sometimes in weird cabinet spots. Such as behind a drawer slide mount or some such.

Seth

Offline Mikeoutrage

  • Posts: 21
Shop cart. Hopefully this will help with keeping the work areas clear.  ::)

Offline Cheese

  • Posts: 6385
FWIW...both of these items came from     https://www.infinitytools.com/

I just received a router bit vise to ease the task of holding the router bit without marring the shaft when changing cutters or bearings. It will hold 1/2", 1/4" & 8 mm diameter bits. It's very nicely machined from black Delrin. I was very surprised and impressed with the quality of the machining.  You can see the flycutter machining marks on the Delrin. The router bit shafts are held stationary with the one-way needle bearings.





I also picked up a Colt 5-Star forstner bit in 1 3/16" diameter to install some Magswitch holdowns. The Colt 5-Star forstner bits are really nice and they're manufactured in Germany or France.

« Last Edit: September 13, 2019, 10:27 AM by Cheese »

Offline kmickey

  • Posts: 5
TSO Precision Triangle kit. I bought it during the Labor Day sale, got it this week.  Really well made, haven’t had a chance to use it yet. Need to design a Systainer insert to hold all the bits and pieces. 

https://tsoproducts.com/tso-products-precision-system-triangles/mtr-18-precision-system-triangle-set/

Offline rst

  • Posts: 2227
Just ordered METABO: WPF 18 LTX 125 (613070860) 5" CORDLESS FLAT HEAD ANGLE GRINDER BARE TOOL...when you can't get into really tight corners.  Bought their 18V tapping drill and vac so already have batteries.

Offline Gregor

  • Posts: 1301
As nothing interesting is coming from festool this year... some spare money was unallocated and a Wabeco BF1243 arrived.
Was time to retire the old (wobbly, as the bearings are worn) drillpress anyway.