Author Topic: A few new tools ...  (Read 854 times)

0 Members and 1 Guest are viewing this topic.

Offline derekcohen

  • Posts: 338
    • In The Woodshop
A few new tools ...
« on: October 27, 2019, 09:11 AM »
... as I prepare for the next furniture build.

I collected some rather nice fiddleback Jarrah from The Timber Bloke for the hall table (for my niece) that is now starting. (It has some nice challenges, but that is all for later) ...



The workshop becomes a dogs breakfast when I get underway, although I tidy up as much as I can. So I take time between builds to clean up, repair anything that needs to be done, and build a few items that have been percolating in my imagination. 

There was a recent posting of a new Moxon dovetail vise ...



More recently, I finally added a bench stop to the end of the bench ...



This has the cork rubber ("crubber", as BenchCrafted refer to it) lining used on the Moxon and legvise. It had excellent non-slip properties (seek it out from outlets that sell gaskets)...



I love it! This stop works so well for face planing.

As many know, I have been field testing pre-production tools for Lee Valley/Veritas for many years. Some of the prototype tools are replaced later with production tools, and I am sometimes left with useable but unsaleable tools. A number of years ago it was bench chisels. It occurred to me that I could turn a 1/4" O1 chisel (which had a few bites in the sides) into a fishtail chisel for half blind dovetails. All that was needed was a hand grinder and some patience. The wood was stained ebony ...



This are so useful when clearing the waste (Rob Lee assures me that fishtail chisels are to be produced by Veritas at some time - their design, not mine). The offset angle is 6:1, which will work with the socket angles I prefer.

A few years ago I made a birds cage awl from carbide for starting screw or drill holes. The square grind here is 25 degrees for the primary bevel and it has a 35 degree micro secondary bevel for durability. The handle is shaped for down force ...



It occurred to me that I could convert very easily a screwdriver into a scratch awl. I wanted this one for marking holes more precisely. 

We've probably all made screwdrivers like these. This one was made some years ago ...



Take a damaged screwdriver insert, insert it into a cordless drill and spin it against a disk sander until it forms a point (at about 20 degrees) ...



Time now to focus on the hall table ...

Regards from Perth

Derek

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Cheese

  • Posts: 6517
Re: A few new tools ...
« Reply #1 on: October 28, 2019, 10:17 AM »
Nice Derek...I assume the bench stop is height adjustable? Tough to see if it's slotted.

As a side note, I purchased some Cork Rubber for a small metal working vise. Here's an interesting comparison between in-kleind Cork Rubber and Crubber. Leather still appears to be a great alternative.  [smile]

https://youtu.be/JiRHgYVFF1k?t=7

Some really nice hand made/modified tools.

I really like your idea of the screwdriver bit turned into an awl. I have 4 different awls but they're all located on the bench. It'd be really convenient to have an awl insert amongst the other driver inserts in my installers set.
« Last Edit: October 28, 2019, 10:21 AM by Cheese »

Offline Cheese

  • Posts: 6517
Re: A few new tools ...
« Reply #2 on: October 29, 2019, 10:49 AM »
@derekcohen I liked your idea of a scribe/awl/punch insert so much that I took 30 minutes out yesterday and fashioned one from a Festool PZ 1 bit.







It fits nicely in the Festool Twin Box




However, after carrying the Twin Box around yesterday, I decided that this was a better method to store the bit...ouch, that point is sharp. [crying]   It's also easier to remove.  [smile]



Offline Dick Mahany

  • Posts: 529
Re: A few new tools ...
« Reply #3 on: October 29, 2019, 11:04 AM »
More excellent ideas here, thanks.  I never seem to run out of projects  [wink]

Offline RKA

  • Posts: 1776
Re: A few new tools ...
« Reply #4 on: October 29, 2019, 01:57 PM »
Great idea Derek!  I can think of a few instances where I had a multi bit driver right in my hand and I'm scrounging around for an awl or center punch. 

LOL Cheese!  As I was scrolling down through the pics I thought "Ouch, that's gonna hurt if he puts the twin box in his pocket"...then I scrolled a little more...yup!   [tongue] 
-Raj