Author Topic: OF1400 5/8 radius for door hinges set up for ujk jig  (Read 887 times)

0 Members and 1 Guest are viewing this topic.

Offline Tiwi63

  • Posts: 2
OF1400 5/8 radius for door hinges set up for ujk jig
« on: June 21, 2021, 12:15 PM »
i need to route a 5/8 radius door hinge, i need a 1 3/8 OD template guide with a straight 1 1/4 router bit, i used a ujk hinges jig, my problem is, i own OF 1400, the 495342 template fits only on an OF 2200, festool don’t make for OF 1400, Anyone knows where to get a brass bushing that fit. Tnx in advance.
« Last Edit: July 13, 2021, 07:22 AM by Tiwi63 »

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline CeeJay

  • Posts: 375
Re: OF1400 5/8 radius for door hinges set up
« Reply #1 on: June 21, 2021, 10:51 PM »
You can use the 40mm copy ring 492186


Sent from my iPhone using Tapatalk

Offline woodbutcherbower

  • Posts: 81
Re: OF1400 5/8 radius for door hinges set up
« Reply #2 on: June 22, 2021, 01:05 PM »
Templates, bushings, copy rings ??? ? To cut a mortise rebate for a door hinge, all you need is the correct diameter cutter and the router's parallel fence ......

Place the hinge on the door edge and draw round it with a sharp pencil. Set the router up with the parallel fence so that the rear edge of the cutter blade exactly lines up with the rear edge pencil line. Make a few test cuts on some scrap to set your plunge depth to the correct hinge plate thickness. Rout carefully making sure that you don't cross the other lines at the top and bottom of the hinge - just make sure your corner radii are in the right place (exactly touching vertical and horizontal lines), and then square the top and bottom edges of the rebate with a chisel. If you're worried about the router wobbling about on the narrow door edge, clamp a block of wood to the side of the door to act as a support sledge to stabilise it.

This one's been done with a 12.7mm cutter which has also then had the corners squared off with a chisel to accept a rectangular hinge, so do likewise with your 1.25" cutter to get your rounded corners and save yourself a world of hassle. The whole process takes 5 minutes maximum - and since you already now have your fence position and plunge depth set up for all of your other hinges, they will take no more than a minute each ....
« Last Edit: June 22, 2021, 01:44 PM by woodbutcherbower »
There's no such thing as a job which is almost perfect. It either is perfect - or it isn't.

Offline CeeJay

  • Posts: 375
Re: OF1400 5/8 radius for door hinges set up
« Reply #3 on: June 22, 2021, 08:39 PM »
Use a 40 mm guides ok and with 1.25 straight bit?
Yes - just need to calculate offset from outside of bit to outside of copy ring to get the offset right.


Sent from my iPhone using Tapatalk

Offline Tiwi63

  • Posts: 2
Re: OF1400 5/8 radius for door hinges set up
« Reply #4 on: June 24, 2021, 06:38 PM »
Ok will try 40 mm and straight bit
Will give you feedback
Tnx

Offline waho6o9

  • Posts: 1610
    • Garage Door Handyman.com
Re: OF1400 5/8 radius for door hinges set up
« Reply #5 on: June 24, 2021, 07:45 PM »
332826-0

This should work......