Author Topic: Festool MFT MultiFunction Table Fastening Set in Systainer  (Read 5394 times)

0 Members and 1 Guest are viewing this topic.

Offline shu

  • Posts: 41
Festool MFT MultiFunction Table Fastening Set in Systainer
« on: December 27, 2017, 07:16 PM »
Hi all,

It seems this set has been discontinued. I can't find it anywhere, at lease in Australia, as of Dec 2017. Can anyone tell me where to buy it please?

Shu

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline copcarcollector

  • Posts: 1457
Re: Festool MFT MultiFunction Table Fastening Set in Systainer
« Reply #1 on: December 27, 2017, 08:10 PM »
Sorry to say these are gone here in the USA as well. I have seen other folks in the UK who were able to find them there recently, but I think many suppliers are out. There is a nice set from Veritas available from Lee Valley:  http://www.leevalley.com/us/wood/page.aspx?p=70681&cat=1,43838,43845

Offline shu

  • Posts: 41
Re: Festool MFT MultiFunction Table Fastening Set in Systainer
« Reply #2 on: December 28, 2017, 03:01 AM »
Many thanks for the info @copcarcollector. I may go for the Lee Valley one. The only thing is that the delivery fee might kill me. I will see.

Offline VesaS

  • Posts: 74
Hobbyist with high demands (for tools)

Offline Mr_Mod

  • Posts: 92
Re: Festool MFT MultiFunction Table Fastening Set in Systainer
« Reply #4 on: December 29, 2017, 01:39 AM »
Give Brian a call at Just tools in South Melbourne, they had a few in there a few days back

Offline yetihunter

  • Posts: 789
Re: Festool MFT MultiFunction Table Fastening Set in Systainer
« Reply #5 on: December 29, 2017, 11:10 PM »
FYI, Carbatec sells Lee Valley/Veritas.  20mm-wise, I only see the Parf Dogs
on their website, but I would presume that they can special order the clamping kit with their next shipment.

Offline smartins

  • Posts: 27
Re: Festool MFT MultiFunction Table Fastening Set in Systainer
« Reply #6 on: January 15, 2018, 08:17 AM »
In ebay.com here one set now, ebay number 263433130195

Before check this out, please sit down to some safe surface. :)

Hi all,

It seems this set has been discontinued. I can't find it anywhere, at lease in Australia, as of Dec 2017. Can anyone tell me where to buy it please?

Shu

Offline Coen

  • Posts: 1612
Re: Festool MFT MultiFunction Table Fastening Set in Systainer
« Reply #7 on: January 18, 2018, 03:55 PM »
Festool 201311 was a limited run. Was a nice set though.

Look at Bessey STC-S-MFT
EAN 4008158040691

The Bessey set has the same clamps, but w/o the nasty adapter to make them fit the MFT. The low-profile stops aren't in the Bessey set however. I wonder why Festool didn't make it (201311) a permanent article.

In ebay.com here one set now, ebay number 263433130195

Before check this out, please sit down to some safe surface. :)

Hi all,

It seems this set has been discontinued. I can't find it anywhere, at lease in Australia, as of Dec 2017. Can anyone tell me where to buy it please?

Shu

 :o
« Last Edit: January 18, 2018, 04:06 PM by Coen »

Offline Coen

  • Posts: 1612
Re: Festool MFT MultiFunction Table Fastening Set in Systainer
« Reply #8 on: July 19, 2018, 05:22 AM »
I see Festool 201311 again under the new items on my local Festool website, as available from September.

Offline Mike S

  • Posts: 32
Re: Festool MFT MultiFunction Table Fastening Set in Systainer
« Reply #9 on: July 20, 2018, 11:09 AM »
The items that are in this kit are all available separately.

I have the low-profile bar type stops I bought from Lee Valley, and dogs are available from many different vendors. 

Truth be told, the low profile bar stops and the bench dogs look identical to the Lee Valley parts that I bought a few months back.

The only thing special in that kit, imho, is the box IF there is a customized insert for all of the bits. 

Offline jobsworth

  • Posts: 6889
  • Festool Baby.....
Re: Festool MFT MultiFunction Table Fastening Set in Systainer
« Reply #10 on: July 20, 2018, 11:30 AM »
Infinity tools has some good stuff for the MFT that Im gonna get.

https://www.infinitytools.com/shop-essentials/clamping/dog-hole-clamps

Offline Coen

  • Posts: 1612
Re: Festool MFT MultiFunction Table Fastening Set in Systainer
« Reply #11 on: July 20, 2018, 10:18 PM »
The items that are in this kit are all available separately.

I have the low-profile bar type stops I bought from Lee Valley, and dogs are available from many different vendors. 

Truth be told, the low profile bar stops and the bench dogs look identical to the Lee Valley parts that I bought a few months back.

The only thing special in that kit, imho, is the box IF there is a customized insert for all of the bits.

It does have an insert to keep all in a nice place. It's just a waste of space, they could have fitted all x2 in the Systainer.

Yes, it's available separately, not only one seller in my country (that I know off).

Infinity tools has some good stuff for the MFT that Im gonna get.

https://www.infinitytools.com/shop-essentials/clamping/dog-hole-clamps


Nice. Did you also look at the Bessey STC-S-MFT?