« previous next »
Pages: [1]   Go Down

Author Topic: Best router lift for Festool 1400 router  (Read 1247 times)

0 Members and 1 Guest are viewing this topic.

Offline Papas Woodshop

  • Posts: 10
Best router lift for Festool 1400 router
« on: January 21, 2021, 07:19 PM »
I need to buy a router life for my Festool 1400 router. I would appreciate any one's experience with lifts that work best for his
Thanks
Papa's Workshop
Logged
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

Offline JimH2

  • Posts: 1017
Re: Best router lift for Festool 1400 router
« Reply #1 on: January 21, 2021, 07:26 PM »
I do not believe there is one other than buying the Festool Router table which pales in comparison to almost any other router table in the $500+ range. The problem with the Festool router is that it cannot be removed from it's plunge mechanism. Look at the offerings of Jessem, Woodpeckers, Powermatic, Rockler, and Kreg to name a few.
Logged

Offline contendernut

  • Posts: 44
Re: Best router lift for Festool 1400 router
« Reply #2 on: January 21, 2021, 07:31 PM »
Jessem makes one for 1010/1400
Logged

Offline fshanno

  • Posts: 1032
Re: Best router lift for Festool 1400 router
« Reply #3 on: January 22, 2021, 01:03 AM »
Quote from: contendernut on January 21, 2021, 07:31 PM
Jessem makes one for 1010/1400

That lift retails for $390.  You can get the Jessem Router Lift II AND a 2.25 hp Bosch 1617 (about the same power as the 1400) for $20 less than just that lift.  Then you'd have a dedicated router and wouldn't have to fiddle with taking it out and putting it in.
Logged
The one thing we learn from history is that we never learn from history.

Offline Roseland

  • Posts: 687
Re: Best router lift for Festool 1400 router
« Reply #4 on: January 22, 2021, 12:39 PM »
Why not get a Triton MOF001 router for less money than a lift?  It has through-the-table height adjustment, auto spindle lock as the collet is raised and 1/2" capacity.

I have an OF1440 and the Triton and don't consider the Festool offering suitable for use in a table.

Andrew
Logged
TS55, MFT/3, OF1400, OF1010, CT26, RS100, ETS125, CXS, MFS400, DF-500, Zobos.

Offline edwarmr

  • Posts: 241
Re: Best router lift for Festool 1400 router
« Reply #5 on: January 22, 2021, 01:02 PM »
Quote from: Roseland on January 22, 2021, 12:39 PM
Why not get a Triton MOF001 router for less money than a lift?  It has through-the-table height adjustment, auto spindle lock as the collet is raised and 1/2" capacity.

I have an OF1440 and the Triton and don't consider the Festool offering suitable for use in a table.

Andrew

I had a Triton with the above table height adjustment. I found it had way too much resistance when trying to raise it with the handle. Going down was no problem but raising it was a pain. I usually just ended up raising it manually below the table. It's definitely an option but it doesn't compare to a Jessem lift in any way, shape, or form in my opinion. The Jessem lift can be operated with one finger.
« Last Edit: January 22, 2021, 01:35 PM by edwarmr »
Logged

Offline edwarmr

  • Posts: 241
Re: Best router lift for Festool 1400 router
« Reply #6 on: January 22, 2021, 01:06 PM »
Quote from: Papas Woodshop on January 21, 2021, 07:19 PM
I need to buy a router life for my Festool 1400 router. I would appreciate any one's experience with lifts that work best for his
Thanks
Papa's Workshop

As was mentioned your two options are the Festool CMS table or the Jessem Rout-R-Lift Prestige.
Here is a link to the Prestige: https://jessem.com/products/rout-r-lift-prestige-for-plunge-based-routers

I have the Prestige and it's great but like others have said you could get a much cheaper plunge router to put in there. The CMS table works great if you get the VL version to attach to your MFT/3 and combine it with the Incra LS Positioner. I love that combo.
Logged

Offline Papas Woodshop

  • Posts: 10
Re: Best router lift for Festool 1400 router
« Reply #7 on: January 23, 2021, 12:36 PM »
Thanks so much for your advice
Consensus is definitely a JessEm lift and a table dedicated router
My father in law who was a fabulous furniture wood worker left me an excellent router table in which I hope to install the new lift. His table has a top of the line Inca fence, circa 1980's, which I hope to use. I need to practice on 3/4 plywood to be sure I can create the lift opening
I really appreciate all of the comments
Mike
Papa's workshop
Logged

Offline Crazyraceguy

  • Posts: 217
Re: Best router lift for Festool 1400 router
« Reply #8 on: January 23, 2021, 08:12 PM »
Quote from: edwarmr on January 22, 2021, 01:02 PM
Quote from: Roseland on January 22, 2021, 12:39 PM
Why not get a Triton MOF001 router for less money than a lift?  It has through-the-table height adjustment, auto spindle lock as the collet is raised and 1/2" capacity.

I have an OF1440 and the Triton and don't consider the Festool offering suitable for use in a table.

Andrew

I had a Triton with the above table height adjustment. I found it had way too much resistance when trying to raise it with the handle. Going down was no problem but raising it was a pain. I usually just ended up raising it manually below the table. It's definitely an option but it doesn't compare to a Jessem lift in any way, shape, or form in my opinion. The Jessem lift can be operated with one finger.

Did you take the spring out of it? there is a black plastic cap on top with one little screw off to the side of it. Loosen the screw, rotate the cap, it will pop up and scare the junk out of you. Pull the spring out and replace the cap. Job done and that resistance is gone. That is the official intent of Triton, most people just never do it. You need it as a plunge router above the table, that's why it is there in the first place. But under the table, you are fighting the spring and gravity. Take it out, it's transformative.
Logged
CSX
DF500 + assortment set
PS420 + Base kit
OF1010
OF1400
MFK700
TS55, FS1080, FS1400 holey, FS1900, FS3000
CT26E + Workshop cleaning set
RO90
RO125
ETS EC 125
RAS115
ETS 125 (2)

Offline edwarmr

  • Posts: 241
Re: Best router lift for Festool 1400 router
« Reply #9 on: January 23, 2021, 08:45 PM »
Quote from: Crazyraceguy on January 23, 2021, 08:12 PM
Quote from: edwarmr on January 22, 2021, 01:02 PM
Quote from: Roseland on January 22, 2021, 12:39 PM
Why not get a Triton MOF001 router for less money than a lift?  It has through-the-table height adjustment, auto spindle lock as the collet is raised and 1/2" capacity.

I have an OF1440 and the Triton and don't consider the Festool offering suitable for use in a table.

Andrew

I had a Triton with the above table height adjustment. I found it had way too much resistance when trying to raise it with the handle. Going down was no problem but raising it was a pain. I usually just ended up raising it manually below the table. It's definitely an option but it doesn't compare to a Jessem lift in any way, shape, or form in my opinion. The Jessem lift can be operated with one finger.

Did you take the spring out of it? there is a black plastic cap on top with one little screw off to the side of it. Loosen the screw, rotate the cap, it will pop up and scare the junk out of you. Pull the spring out and replace the cap. Job done and that resistance is gone. That is the official intent of Triton, most people just never do it. You need it as a plunge router above the table, that's why it is there in the first place. But under the table, you are fighting the spring and gravity. Take it out, it's transformative.

Yeah I took the spring out. It’s been about 5 years since I had it. It’s just not as simple as the Jessem lifts. Drilling the plate for it also wasn’t easy. I think now they sell predrilled plates for it. It’s definitely an option for a router table but it doesn’t have the accuracy or ease of a nice lift in my opinion. You also have to drop the handle blindly in the hole until you get it to attach to the Triton router which can be a pain. I found I could adjust the height faster going below the table,
Logged

Offline Crazyraceguy

  • Posts: 217
Re: Best router lift for Festool 1400 router
« Reply #10 on: January 23, 2021, 09:10 PM »
I always reach below the table to adjust it, you have to for the lock lever anyway. I really like the squeeze-ring thing for the gross adjustment too. It's far better than turning the crank anyway.
I mentioned the spring because I had one of the smaller 2 1/4 HP models several years ago and didn't remove it when initially setting it up. I did end up taking it out after some use.
I do have a pre-drilled (Kreg) plate and it even has the adjuster hole drilled too. The aluminum plate I had before was drilled for the router mounting, but not the adjuster hole? never made sense to me.
I have never had an actual lift, but I'm thinking about getting one from Sauter shop. They have one that tilts which would be great for me, but it requires a 43mm mount spindle. Getting one of those in 100 volt American is not so easy.
Logged
CSX
DF500 + assortment set
PS420 + Base kit
OF1010
OF1400
MFK700
TS55, FS1080, FS1400 holey, FS1900, FS3000
CT26E + Workshop cleaning set
RO90
RO125
ETS EC 125
RAS115
ETS 125 (2)

Offline edwarmr

  • Posts: 241
Re: Best router lift for Festool 1400 router
« Reply #11 on: January 23, 2021, 09:19 PM »
Quote from: Crazyraceguy on January 23, 2021, 09:10 PM
I always reach below the table to adjust it, you have to for the lock lever anyway. I really like the squeeze-ring thing for the gross adjustment too. It's far better than turning the crank anyway.

That’s exactly what I used to do with the gross adjustment knob lol. Like you said you have to lock it below the table anyway so it kind of defeats the purpose of the above table adjustment. I hope you’re able to find a lift that works out for you!
Logged
Pages: [1]   Go Up
« previous next »