Having trouble with your Festool power tool? Well, we're here to help you. Before posting to the forum, give us a chance to diagnose and resolve your issue. In the U.S. and Canada, call us toll-free at 888-337-8600 on Monday-Friday between 8a-5p EST or contact us via email at service@festoolusa.com. For other countries, please visit http://www.festool.com for contact information for your local Festool service department.

Author Topic: Vacuum Boom Sag  (Read 3337 times)

0 Members and 1 Guest are viewing this topic.

Offline yucholian

  • Posts: 5
Vacuum Boom Sag
« on: April 23, 2007, 03:01 PM »
I've had my vacuum boom for 1 week and noticed the sag in the boom.  After careful look, I noticed the white nylon swivel piece is bent from the stress.  I talked to Woodcraft where I bought it and they said Festool has aluminum replacement part for that and I should call them.  So I did call Festool direct.  Gentleman on the phone (tech support) says they don't have such aluminum piece and that he hasn't heard of the sag issues with the nylon piece.  He also said that if I had problems, I NEEDED to go through Woodcraft, not direct to Festool.  He said that if I contact Woodcraft, they could have a replacement nylon part sent to me.  But wouldn't that sag too?

So here are my questions:
1)  Has anyone else noticed the sag at the nylon piece?  If so, did you fix it or left it?  I'm thinking it will continue to get worse, but maybe that's a wrong assumption.
2)  Is this common with Festool that I have to go through the place of purchase rather than directly with them?

Not trying to start an arguement, I just don't know.  This is the first "issue" I've had with all my Festools, I don't know what normal with their process.

Thanks in advance.


Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Steve Rowe

  • Posts: 828
  • Teach them safety when they are young.
Re: Vacuum Boom Sag
« Reply #1 on: April 23, 2007, 05:34 PM »
Yes - I have noticed sag but never thought much of it.  I have had the boom arm since last September.  If I were several inches taller it would probably bother me.
Steve

Offline tvgordon

  • Posts: 501
  • Springfield, Ohio
Re: Vacuum Boom Sag
« Reply #2 on: April 23, 2007, 06:31 PM »
I've only had my boom arm a month or so but I noticed a slight sag, just a little off from being parallel with the floor.  It hasn't affected how it swings from side to side so I have not worried about it.
Tom.

Offline Skip Jeffrey

  • Posts: 7
  • Pasadena, Maryland
Re: Vacuum Boom Sag
« Reply #3 on: April 23, 2007, 09:03 PM »
I posted a concern about the same problem back in March. I suggest you carefully inspect the nylon piece that fits into the tubes. I actually took mine apart and noticed the piece had split, causing the arm to sag. I had to replace the piece but have been thinking of having an aluminum piece machined. The weight of the boom arm exerting on that nylon piece has me concerned. I dont want to have it fracture and fall.
Every day above ground is a good one!

Offline Corwin

  • Posts: 2644
Re: Vacuum Boom Sag
« Reply #4 on: April 24, 2007, 02:02 AM »
Mine started down this path shortly after I first got it.  Spoke with Bob, then an independent Festool rep -- there was word about an aluminum replacement...  Well, as I recall the word was that there were three parts (or so) that someone had made and that Festool would be making them soon.  So, I have been waiting...  For now I have been removing the Boom Arm when not in use.  Hope the situation changes in the near future.

Corwin