Having trouble with your Festool power tool? Well, we're here to help you. Before posting to the forum, give us a chance to diagnose and resolve your issue. In the U.S. and Canada, call us toll-free at 888-337-8600 on Monday-Friday between 8a-5p EST or contact us via email at service@festoolusa.com. For other countries, please visit http://www.festool.com for contact information for your local Festool service department.

Author Topic: Kapex fence not square  (Read 3484 times)

0 Members and 1 Guest are viewing this topic.

Offline abarraza5

  • Posts: 2
Kapex fence not square
« on: September 30, 2015, 02:44 PM »
So I noticed my fence was not square while cutting a board. Problem is it's just on one side, and the body is one piece. I tried emailing Festool, I got a response but after sending pictures response stopped.
« Last Edit: September 30, 2015, 06:18 PM by abarraza5 »

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline TylerC

  • Posts: 1084
Re: Kapex fence not square
« Reply #1 on: September 30, 2015, 03:09 PM »
Sorry that looks like your saw is off. Give service a call about getting it repaired. They should be able to take care of you at 1-888-337-8600.

Let me know if you have trouble reaching someone or if you need any additional help.
This account is retired. Please address all Festool questions to @festool usa.

Offline VaDimZH

  • Posts: 181
Re: Kapex fence not square
« Reply #2 on: September 30, 2015, 06:25 PM »
Is it possible to adjust it?


Offline Peter Halle

  • Global Moderator
  • *
  • Posts: 12038
  • MacGyver - My boy 2010 - 2019 RIP
Re: Kapex fence not square
« Reply #3 on: September 30, 2015, 06:41 PM »
I am not speaking for Festool here.  There are fence mounting bolts that if you loosen them on the "bad side" might release tension and allow it to come into plane.  Once loosened it might also be able to force that side into position.  My recollection is that has worked for some here. 

Peter

Offline chris s

  • Posts: 107
Re: Kapex fence not square
« Reply #4 on: October 02, 2015, 08:36 AM »
If that is an aluminum framing square, they have been known to be bowed. I would try to check it with a known straight edge.
                                             Chris

Offline TomE

  • Posts: 131
Re: Kapex fence not square
« Reply #5 on: October 02, 2015, 10:16 AM »
Aluminum or not, I've not seen any framing square that far off at the edge, some bow at the flat maybe.

It's the fence, resetting it might be better with more a precise edge but even setting it to his square would be beneficial.

Offline Lbob131

  • Posts: 469
Re: Kapex fence not square
« Reply #6 on: October 02, 2015, 02:00 PM »
My Makita  miter saw was   off like that.
 Just loosened the  securing  bolts  and  there  was enough play  to allow it to be  aligned  perfectly straight  again.
The designs look very similar.

Have this saw about 10 years. Pushing heavy stock  against   the fence  caused  the  alignment   issue  and also a few kick backs  when the blade snagged  in bowed lumber.
« Last Edit: October 02, 2015, 02:03 PM by Lbob131 »