Having trouble with your Festool power tool? Well, we're here to help you. Before posting to the forum, give us a chance to diagnose and resolve your issue. In the U.S. and Canada, call us toll-free at 888-337-8600 on Monday-Friday between 8a-5p EST or contact us via email at service@festoolusa.com. For other countries, please visit http://www.festool.com for contact information for your local Festool service department.

Author Topic: LR 32 rod problem- SOLVED. Thanks FESTOOL!  (Read 2434 times)

0 Members and 1 Guest are viewing this topic.

Offline David Fox

  • Posts: 32
LR 32 rod problem- SOLVED. Thanks FESTOOL!
« on: October 06, 2018, 08:18 PM »
THE rods for the parallel adjustment in my LR32 kit are losing their markings. Almost impossible to set it now due to the condition of the millimeter marking. I haven't used it THAT much. They appear to be printed onto the rods instead of etched? Nothing in the systainer is rolling around, and the way is all fits in there, the rods don't rub against anything. Anyone else have this problem?
« Last Edit: November 17, 2018, 07:36 PM by David Fox »

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

Offline jobsworth

  • Posts: 6018
  • Festool Baby.....
Re: LR 32 rod problem
« Reply #1 on: October 06, 2018, 09:01 PM »
Not me and I use mine a lot. I
Have you called festool service or your dealer yet?

I have 2 sets of those stops.
I bought a extra set so i can adj them once. one set at 35mm te other at 22mm for hinges. I am going to buy a couple extra end stops so I will be able to do 2 cabinets at the same to me

Offline Dick Mahany

  • Posts: 551
Re: LR 32 rod problem
« Reply #2 on: October 07, 2018, 09:03 AM »
Mine are 3 yrs old and used a lot, but not having this happen.  I wouldn't hesitate to give Festool service a call.  Possibly a bad run of markings.  It is difficult enough as is to see the markings to begin with (to me) and if they wore off, that would be bad.

Offline Gregor

  • Posts: 1542
Re: LR 32 rod problem
« Reply #3 on: October 07, 2018, 10:33 AM »
Mine are fine too.

The rods are somewhat strange though as of being massively massive, compared to everything else from Festool.

Offline David Fox

  • Posts: 32
Re: LR 32 rod problem
« Reply #4 on: October 22, 2018, 09:30 PM »
They called me to tell me they were sending one rod they had in stock. Next month, they will send the other. I just received the first one this past week.

Offline David Fox

  • Posts: 32
Re: LR 32 rod problem
« Reply #5 on: November 17, 2018, 07:36 PM »
update on the rods. I have received repacements for both rods. My problem is solved. New idea, place the new rod next to the old rod and transfer the markings with a fine sharpie, then using a dremel tool, and thin cut off abrasive, etch the marking in my old rods.