Author Topic: Drawing file for Conturo-AP Table DXF or PDF?  (Read 1621 times)

0 Members and 1 Guest are viewing this topic.

Offline rtfosmoe

  • Posts: 8
Drawing file for Conturo-AP Table DXF or PDF?
« on: October 20, 2017, 02:48 PM »
Hello,

I was wondering if anyone has created a Conturo-AP MDF Tabletop drawing?  I just recently purchased a Conturo and would like swap out my normal Multifunction tabletop when I need to do edgebanding.   I have access to a CNC which I can create the table top. Additionally, I have found the discussion on FOG and files associated with the Multifunction table top. Any assistance would be greatly appreciated.

Thanks,

Rich

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Ralph Mignano

  • Retailer
  • *
  • Posts: 35
Re: Drawing file for Conturo-AP Table DXF or PDF?
« Reply #1 on: April 05, 2019, 05:21 PM »
Hi. Did you ever get the file for this ?
TS 55 R, CTL MIDI, RAILS 1400mm, DF 500 Q, OF 1400, CMS-OF, CMS-GE GB 240V, CMS-TS55, ETS 150/5, BS 75 E, MFT/3, KS120, MFK 700 EQ, T 18+3 FL, CTL 36,PS 420 EBQ, ETS EC 150/3, RTS 400 REQ, FS5000/2, FS 1400/2-LR 32, SYSROCK BR10, VAC SYS Set SE1, SYS3-Set SURFIX, FS-PA, FS-PA-VL, LR 32-SYS

Offline Cheese

  • Posts: 6463
Re: Drawing file for Conturo-AP Table DXF or PDF?
« Reply #2 on: April 05, 2019, 05:26 PM »
This may help...

@rtfosmoe

Offline Ralph Mignano

  • Retailer
  • *
  • Posts: 35
Re: Drawing file for Conturo-AP Table DXF or PDF?
« Reply #3 on: April 06, 2019, 01:41 PM »
This may help...

@rtfosmoe

Am I missing something?
TS 55 R, CTL MIDI, RAILS 1400mm, DF 500 Q, OF 1400, CMS-OF, CMS-GE GB 240V, CMS-TS55, ETS 150/5, BS 75 E, MFT/3, KS120, MFK 700 EQ, T 18+3 FL, CTL 36,PS 420 EBQ, ETS EC 150/3, RTS 400 REQ, FS5000/2, FS 1400/2-LR 32, SYSROCK BR10, VAC SYS Set SE1, SYS3-Set SURFIX, FS-PA, FS-PA-VL, LR 32-SYS

Offline Cheese

  • Posts: 6463
Re: Drawing file for Conturo-AP Table DXF or PDF?
« Reply #4 on: April 06, 2019, 02:23 PM »
Am I missing something?

Well, rtfosmoe posted this almost 2 years ago so it’s unlikely he’s still actively searching the board everyday for a reply. It’s like a needle in a haystack.

The @ symbol in front of his name sends a message directly to his email saying that he’s been mentioned in a conversation on the FOG.

Just trying to increase the likelihood of him/her answering your question.