Author Topic: Vacuum Clamp System - Filters option  (Read 653 times)

0 Members and 1 Guest are viewing this topic.

Offline bigdogmn73

  • Posts: 3
Vacuum Clamp System - Filters option
« on: January 11, 2022, 04:01 PM »
If anyone out there is in need of a filter for their vacuum Clamp System they can be found here. I ordered one from one of the Festool dealers and when I got it I figured out I could have ordered it from the below for $4.99 compared to $50 plus I assume the Festool dealers won't carry it long term and they said to replace them yearly.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

Offline _Ben_

  • Posts: 44
Re: Vacuum Clamp System - Filters option
« Reply #1 on: January 12, 2022, 04:10 PM »

Offline GarryMartin

  • Posts: 1907
Re: Vacuum Clamp System - Filters option
« Reply #2 on: January 13, 2022, 07:26 AM »
Spot on. The actual part is a Mann Hummel WK 42/2 Fuel Filter.

Just bear in mind that you don't get the clips and o-rings that you get in the Festool packaging so will need to source those separately if you need them.

Offline woodwise

  • Posts: 16
Re: Vacuum Clamp System - Filters option
« Reply #3 on: January 13, 2022, 08:05 AM »
Thanks! Very useful information.

Online DynaGlide

  • Posts: 1196
Re: Vacuum Clamp System - Filters option
« Reply #4 on: January 13, 2022, 08:14 AM »
Thanks. I grabbed two. If I ever get the fittings I ordered to replace the QD couplings I'll start a cross reference for the Vac-Sys parts thread.

Instagram @matts.garage

Offline Joe Felchlin

  • Posts: 214
  • Just another day in paradise - Livin’ the dream!
Re: Vacuum Clamp System - Filters option
« Reply #5 on: January 13, 2022, 04:59 PM »
Thx Guys👍
Scored 4 for myself.
$26 and change for 4 - Including S&H.
FESTOOL: CT26, CT33 E HEPA Dust Extractors, MFT 1080, MFT-3, TS 55 REQ-F-Plus USA, TS75 EQ, Guide Rails: 1080's/1400/3000mm, LR 32-SYS/Holey Rail, Parallel Guides & Extensions, Plunge Routers: OF1400 EQ & OF1010, Sanders: RO125 FEQ Rotex, LS 130 EQ Linear Detail, DX93E Detail, Drills: PDC 18/4 Li QuaDrive Cordless Drill Set, C12 Cordless, CXS Cordless Compact Driver, SYS-Centrotec-Set, Dominos: XL DF 700 EQ Plus Tenon Joiner Set, DF 500 Tenon Joiner, VAC SYS: System Set, SE 2, Accessory Set | WOODPECKERS: DF 500 Offset Base System | BOSCH: 5412L Compound Miter Saw, 4100-09 10-Inch Table Saw | POWERMATIC: 60HH 8" Jointer, PWBS 14" Bandsaw w/Riser Block | MAKITA: 2012NB Bench Top Planer | JESSEM: Mast-R-Lift XL/Fence/Slide, Rout-R-Plate/Table Stand | RIKON: 50-120 6inX48in Belt-Disc Sander | JET: JBOS-5 Benchtop Oscillating Spindle Sander | PORTER CABLE: 7518 and 690LVRS Routers, 557 Pro Plate Joiner, 16/18/23 Gauge Nailers | LEIGH JIG: D4R 24 Pro Dovetail Jig, | LIE-NIELSEN: Almost every hand plane | DOWELMAX: 3/8" and 1/4" | KREG: K3 Master System | FEIN: Multimaster FMM 250 Q Kit | TORMEK: Super-Grind 2000 | DUST DEPUTY: Industrial (ALL) Steel Deluxe Cyclone (2)

Offline Bob D.

  • Posts: 2473
Re: Vacuum Clamp System - Filters option
« Reply #6 on: January 13, 2022, 10:58 PM »
".... Including S&H."

S&H as in Green stamps?

Didn't know they still give out S&H Green Stamps?  [big grin]
It's a table saw, do you know where your fingers are?