Author Topic: OF1010 - diy router table?  (Read 1096 times)

0 Members and 1 Guest are viewing this topic.

Offline kerf

  • Posts: 8
OF1010 - diy router table?
« on: October 30, 2019, 09:32 AM »
Hello,
I recently purchased the OF1010  [smile]
Whilst researching which router to buy I came across an article showing the 1010 in a homemade mini table!
I’m pretty sure it was on this forum. However, I’ve searched and can’t track it down!
Does anyone know if it exist here, or anywhere else for that matter??
Thanks, Dave (Kent, UK)

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline xedos

  • Posts: 117

Offline kerf

  • Posts: 8
Re: OF1010 - diy router table?
« Reply #2 on: October 30, 2019, 11:27 AM »
Not exactly what I had in mind but worth a look!
Many thanks, Dave

Offline jobsworth

  • Posts: 5895
  • Festool Baby.....
Re: OF1010 - diy router table?
« Reply #3 on: October 30, 2019, 12:59 PM »
Here ya go




Offline kerf

  • Posts: 8
Re: OF1010 - diy router table?
« Reply #4 on: October 30, 2019, 02:25 PM »
Hey thanks, very informative. The guy that made that had a lot of time on his hands, impressive!
The one I recall was a lot smaller, and easier to build..!! [smile]
Thanks for the link [smile]
Dave

Offline xedos

  • Posts: 117
Re: OF1010 - diy router table?
« Reply #5 on: October 30, 2019, 11:45 PM »
The Benchworks guy from Belgium made something to fit in a systainer.

Is that what you're looking for ?
« Last Edit: October 30, 2019, 11:56 PM by xedos »

Offline kerf

  • Posts: 8
Re: OF1010 - diy router table?
« Reply #6 on: October 31, 2019, 04:11 AM »
The table was more like the one in this ytube video, but OF1010 specific
(fast forward to 4min)
Making box joints is the aim so will no doubt modify the video example to suit my router!
Thanks for the suggestions 👍

Offline kerf

  • Posts: 8
Re: OF1010 - diy router table?
« Reply #7 on: October 31, 2019, 04:14 AM »
Newbie problems... YouTube link did not display in above post  [eek]

Offline Bob D.

  • Posts: 1359
Re: OF1010 - diy router table?
« Reply #8 on: October 31, 2019, 06:08 AM »
What browser are you using.
-----
It's a table saw, do you know where your fingers are?

Offline kerf

  • Posts: 8
Re: OF1010 - diy router table?
« Reply #9 on: October 31, 2019, 10:00 AM »
Safari on iPad..!

Offline usernumber1

  • Posts: 67
Re: OF1010 - diy router table?
« Reply #10 on: October 31, 2019, 01:04 PM »
embedded youtube link with no timestamp. yikes

i've fixed it for you

https://youtu.be/nsgy6d4365k?t=239

Offline kerf

  • Posts: 8
Re: OF1010 - diy router table?
« Reply #11 on: October 31, 2019, 01:57 PM »
Genius! Thanks
The problem was no-time stamp or safari?

Offline usernumber1

  • Posts: 67
Re: OF1010 - diy router table?
« Reply #12 on: October 31, 2019, 06:29 PM »
Genius! Thanks
The problem was no-time stamp or safari?

safari - timestamp is kinda tricky without PC, you need to right click on a youtube video itself

Offline gunnyr

  • Posts: 177
    • Compass Custom Creations
Re: OF1010 - diy router table?
« Reply #13 on: November 03, 2019, 07:45 PM »
Hello,
I recently purchased the OF1010  [smile]
Whilst researching which router to buy I came across an article showing the 1010 in a homemade mini table!
I’m pretty sure it was on this forum. However, I’ve searched and can’t track it down!
Does anyone know if it exist here, or anywhere else for that matter??
Thanks, Dave (Kent, UK)

Jerry Works published an article several years ago; Making the Festool Multi-Function Table into vertical and horizontal router tables the easy way  Maybe that's is what you remember seeing:
http://thedovetailjoint.squarespace.com/storage/Adding%20routers%20to%20a%20Festool%20MFT%20reduced.pdf
Semper Fi,
Jeff

TS 55 REQ|HKC 55|PSB 420|DF 500|ETS EC 125/3 EQ|ETS 150/3|DTSC 400|RO 90|RO 150|OF 1400|MFK 700|LR 32|MFS 400/700|CXS (2)|PDC 18|DWC 18-4500|CT MIDI|CT 26|CT 48|MFT/3 (2)|VAC SYS-SET|DUO-SET|SYSLITE KAL II
US Marines - UK Wildcats - Cincinnati Reds

Offline kerf

  • Posts: 8
Re: OF1010 - diy router table?
« Reply #14 on: November 04, 2019, 01:38 PM »

Jerry Works published an article several years ago; Making the Festool Multi-Function Table into vertical and horizontal router tables the easy way  Maybe that's is what you remember seeing:
http://thedovetailjoint.squarespace.com/storage/Adding%20routers%20to%20a%20Festool%20MFT%20reduced.pdf

That isn't the article, unfortunately, but very interesting all the same..!
Thanks for posting the link  [smile]