« previous next »
Pages: [1]   Go Down

Author Topic: Flatten a slab with OF1400  (Read 3519 times)

0 Members and 1 Guest are viewing this topic.

Offline juststartingout

  • Posts: 57
    • https://www.instagram.com/aq_designworks/
Flatten a slab with OF1400
« on: November 02, 2018, 11:35 AM »
Hi all,

I'm looking to flatten a 10 foot slab 40 inches wide and 2.5 inches thick.  I only have an OF1400 and am wondering if its underpowered for a 1 inch Freud straight bit?

Anyone out here have words of wisdom?

Thanks,

Oscar
Logged
MFT3, TS55, CT 26, OF1400, RO90, RO150, Carvex PS 420 EBQ, Domino 500, and dreaming of a Kapex.
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

Online Gregor

  • Posts: 1710
Re: Flatten a slab with OF1400
« Reply #1 on: November 02, 2018, 11:55 AM »
Logged

Offline rvieceli

  • Posts: 1201
Re: Flatten a slab with OF1400
« Reply #2 on: November 02, 2018, 03:32 PM »
Cool. that's a thread that I started.  [big grin]

@juststartingout the router should work ok. Just remember it's not a 5 HP spindle in a CNC, so don't try to hog off 3/4 of an inch in a single pass.

That's a good size slab. I have noticed lately that many of the folks that specialize in selling slabs have started offering flattening services as well. So you might want to inquire.

Ron
Logged

Offline jobsworth

  • Posts: 6196
  • Festool Baby.....
Re: Flatten a slab with OF1400
« Reply #3 on: November 03, 2018, 12:19 PM »
If it were me, Id use a RO150 with a blue pad (hard pad) start with a very course grit and work through the grits or a 850 planer.

Even better find a shop with a wide belt sander and see if they will run it through it a few times for you. Youmight have to kick him a few bucks but it will be worth it
« Last Edit: November 03, 2018, 12:59 PM by jobsworth »
Logged

Online SRSemenza

  • Global Moderator
  • *
  • Posts: 9230
  • Finger Lakes Region, NY State , USA
Re: Flatten a slab with OF1400
« Reply #4 on: November 03, 2018, 01:55 PM »
The 1400 will spin a 1" straight bit ........... no problem.

Seth
Logged

Offline Svar

  • Posts: 2092
Re: Flatten a slab with OF1400
« Reply #5 on: November 03, 2018, 01:59 PM »
As mentioned before 1" or 1.5" bit is fine for a 1400 Watt router. I prefer dish carving bit to straight one for flattening. It has rounded corners and makes transitions between passes less visible.
« Last Edit: November 03, 2018, 02:56 PM by Svar »
Logged

Offline Svar

  • Posts: 2092
Re: Flatten a slab with OF1400
« Reply #6 on: November 03, 2018, 02:02 PM »
Quote from: jobsworth on November 03, 2018, 12:19 PM
Even better find a shop with a wide belt sander and see if they will run it through it a few times for you. Youmight have to kick him a few bucks but it will be worth it
And for few more bucks they'll make you the entire table...  [poke]
Logged

Offline jobsworth

  • Posts: 6196
  • Festool Baby.....
Re: Flatten a slab with OF1400
« Reply #7 on: November 03, 2018, 08:08 PM »
Quote from: Svar on November 03, 2018, 02:02 PM
Quote from: jobsworth on November 03, 2018, 12:19 PM
Even better find a shop with a wide belt sander and see if they will run it through it a few times for you. Youmight have to kick him a few bucks but it will be worth it
And for few more bucks they'll make you the entire table...  [poke]

and for a few more bucks he buy one prefinished  [doh]
Logged

Offline waho6o9

  • Posts: 1549
    • Garage Door Handyman.com
Re: Flatten a slab with OF1400
« Reply #8 on: November 03, 2018, 11:27 PM »
Easy peasy, it's a work horse, watch your feeds and speeds and it'll flatten that slab.

287182-0
Logged

Offline lwoirhaye

  • Posts: 252
Re: Flatten a slab with OF1400
« Reply #9 on: November 04, 2018, 12:49 AM »
I'd use a cheaper fixed base router personally.    Ebay special.

I know doing it yourself sounds exciting but you might do as some other have suggested and call around to see about wide belt service.
Logged

Offline hdv

  • Posts: 143
Re: Flatten a slab with OF1400
« Reply #10 on: November 04, 2018, 04:35 AM »
I use the Festool sled (MFS-FS) and routing template (MFS 700) combined with my OF1400 for this. Search for Festool 495648 Routing Slide. Up to now it has done a good job for me. Maybe it will meet your needs as well?
Logged

Offline Farming_Sawyer

  • Posts: 124
  • Sawyer, builder, winemaker, farmer, chef
    • Foley's Custom Sawmill
Re: Flatten a slab with OF1400
« Reply #11 on: November 04, 2018, 07:50 AM »
Router sled is about the only thing that works to take cup And twist out of a large piece. Much nicer to work on a 200lb or greater piece without having to constantly move it.
Logged
CT 26E, RO125, sys-mft, sys-toolbox, a bunch of 30 year old tools I'm looking to replace.

Offline waho6o9

  • Posts: 1549
    • Garage Door Handyman.com
Re: Flatten a slab with OF1400
« Reply #12 on: November 04, 2018, 08:23 AM »
Make a pair of winding sticks to check for twists in the slab.

Pubic Domain:
287186-0
Logged

Offline rst

  • Posts: 2402
Re: Flatten a slab with OF1400
« Reply #13 on: November 04, 2018, 06:20 PM »
I use 8020 extrusions...
287222-0  I have 96" 1530s that I use but I could get up to 20'ers if I was to buy from a distributor rather than the 8020 Ebay store.
I also have 1545s although shorter versions.  These could be used for longer stiffer versions for the side quides.
« Last Edit: November 04, 2018, 06:24 PM by rst »
Logged

Offline Vondawg

  • Posts: 353
Re: Flatten a slab with OF1400
« Reply #14 on: November 04, 2018, 09:38 PM »
Logged
There are no mistakes....just new designs.

Offline Cheese

  • Posts: 7387
Re: Flatten a slab with OF1400
« Reply #15 on: November 05, 2018, 01:03 AM »
Quote from: Svar on November 03, 2018, 01:59 PM
As mentioned before 1" or 1.5" bit is fine for a 1400 Watt router. I prefer dish carving bit to straight one for flattening. It has rounded corners and makes transitions between passes less visible.

I’ve used a 3/4” or 1” diameter bowl bit in a 1010 for flattening Brazilian cherry. It worked fine and reduced the “stepping” transitions in the flatenning process. Less work for the sander.  [big grin]
« Last Edit: November 05, 2018, 02:19 AM by Cheese »
Logged

Offline Sparktrician

  • Posts: 3964
Re: Flatten a slab with OF1400
« Reply #16 on: November 05, 2018, 10:03 AM »
Quote from: Cheese on November 05, 2018, 01:03 AM
Quote from: Svar on November 03, 2018, 01:59 PM
As mentioned before 1" or 1.5" bit is fine for a 1400 Watt router. I prefer dish carving bit to straight one for flattening. It has rounded corners and makes transitions between passes less visible.

I’ve used a 3/4” or 1” diameter bowl bit in a 1010 for flattening Brazilian cherry. It worked fine and reduced the “stepping” transitions in the flatenning process. Less work for the sander.  [big grin]

I use an Amana Tool 45453 carbide-tipped straight plunge bit in either the OF 2200 or the OF 1400.  Another good option is the Whiteside #6220 Spoilboard Cutter.  No bowls to sand out either way, @Cheese. 
Logged
- Willy -

 "Remember, a chip on the shoulder is a sure sign of wood higher up." - Brigham Young
Pages: [1]   Go Up
« previous next »