Having trouble with your Festool power tool? Well, we're here to help you. Before posting to the forum, give us a chance to diagnose and resolve your issue. In the U.S. and Canada, call us toll-free at 888-337-8600 on Monday-Friday between 8a-5p EST or contact us via email at service@festoolusa.com. For other countries, please visit http://www.festool.com for contact information for your local Festool service department.

Author Topic: KS 120 Dimensions  (Read 712 times)

0 Members and 1 Guest are viewing this topic.

Offline keithchalfant

  • Posts: 4
KS 120 Dimensions
« on: January 31, 2022, 12:04 PM »
Is there a detailed drawing of the most recent KS 120 with dimensions?  I saw one on here, but it was from a few years ago and showed the width at 24 1/8”, while the Festool website shows the width now at 28”. I have a saw stand I made for another miter saw, and I’m trying to figure out if the new Kapex will fit.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline sauropod

  • Posts: 3
Re: KS 120 Dimensions
« Reply #1 on: February 12, 2022, 07:15 PM »
24 1/8” is what mine looks like in standard 0° angle (square crosscut).  I suspect the 28” might be measuring when the Kapex angle is set to 60° as seen in my pics attached.  When you do that the black knob/pedal for the angle stop protrudes about 4” from the width of the frame, and the back of the saw protrudes slightly from the left side of the base measuring in at a total 28”.

So since the angle adjustment pedal/knob sits slightly below the work surface I suspect that if you are building a miter saw cavity to place the saw into, you need to account for the full 28”.  Or ensure that the cavity depth is not such that it would impede the knob/front of saw and leave an extra width on the left side for the back to swivel around and exceed the left side width by a bit, although you can see from the pics the back of the saw is going to be much higher than the work surface.  The 28” accounts for that knob/pedal looking at it from front in the pic at the 60° angle.

Hope the pics help.

« Last Edit: February 12, 2022, 07:42 PM by sauropod »

Offline squarecut

  • Posts: 147
  • It Is What It Is
Re: KS 120 Dimensions
« Reply #2 on: February 13, 2022, 02:35 PM »
The footprint of the Kapex is 24-1/8", however to accommodate the 60-degree angle of the righthand swing you must add another 4" to the width of the miter station cavity. I recently completed my Kapex miter saw station and built it 28-7/8" in width and mounted the Kapex off center by one inch to the left due to space considerations. Of course, if you have enough space that would not be necessary.

See attached photos
« Last Edit: February 13, 2022, 03:53 PM by squarecut »
Largest private sawdust producer in Huntington NY