Having trouble with your Festool power tool? Well, we're here to help you. Before posting to the forum, give us a chance to diagnose and resolve your issue. In the U.S. and Canada, call us toll-free at 888-337-8600 on Monday-Friday between 8a-5p EST or contact us via email at service@festoolusa.com. For other countries, please visit http://www.festool.com for contact information for your local Festool service department.

Author Topic: Infeed for a CMS-GE Router Table  (Read 885 times)

0 Members and 1 Guest are viewing this topic.

Offline c_dwyer

  • Posts: 185
Infeed for a CMS-GE Router Table
« on: September 30, 2021, 09:40 PM »
Hi All:
Does anyone know if the Extension Table TSB/1-MW 1000 for the Mobile Workshop will fit the infeed side of the CMS-GE like the Right Side Kapex UG wing will?

I've seen a few pictures of CMS-GE owners using the Kapex wing or creating their own infeed tables with Kapex wing parts, but just wondering if the Extension Table would be better given that I'd be able to pile stuff on it afterwards like all of my other workbenches.

Given the "system" culture of Festool, I'm assuming it will fit and end up the same height, but we all know what happens when one assumes. Any ideas?

Thank you in advance.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline c_dwyer

  • Posts: 185
Re: Infeed for a CMS-GE Router Table
« Reply #1 on: September 30, 2021, 09:53 PM »
Never mind, found it on the Festool web site (should have looked first):

"The MW 1000 Extension Table is the perfect platform for working on the jobsite. The Extension Table can be combined with the Festool MFT/3 Table or CMS Router Table for additional workspace or material support."

Seems like a cheaper (by a $100) way to go than the Kapex UG wing, which isn't wide enough to hold very much when not in use.  Maybe that's a good thing.

Offline Roachmill

  • Posts: 314
Re: Infeed for a CMS-GE Router Table
« Reply #2 on: October 01, 2021, 06:12 AM »
It'll depend on the width of what you're wanting to run through the CMS; as in the MW table will support much wider stock but it'll also get in the way for thinner stuff like trim when compared to a UG wing. With the MW table connected as an infeed support you have to stand further away from CMS router fence where a UG wing lets you stand much more inline with it. The MW table could possibly (never tried it) be shimmied across a bit to allow you to stand more inline with the fence and is likely the more versatile option if you're working with wide pieces.

IIRC, the widest board I've run through the CMS with a UG wing for infeed support it was ~150mm / 6" and that was easy enough.

Offline Sparktrician

  • Posts: 4273
Re: Infeed for a CMS-GE Router Table
« Reply #3 on: October 01, 2021, 06:59 AM »
I use the extra table on the infeed side without difficulty.  One thing to be remembered is that the tables should be co-planar with the CMS top plate, and they're built to be adjustable, but one must make the effort to adjust and verify them to get the best quality jobs.
- Willy -

  "Show us a man who never makes a mistake and we will show a man who never makes anything. 
  The capacity for occasional blundering is inseparable from the capacity to bring things to pass."

 - Herman Lincoln Wayland (1830-1898)